Search results

Create the page "Transmit Only" on this wiki! See also the search results found.

• Channel Tab
  ...- because it is a Transmitter. The FlexTT5, a Transceiver, will show both Transmit and Receive options, because it perform both operations.'' ====ControlTL Transmit Priority at X-Sync (Nikon Only):====
  3 KB (503 words) - 09:53, 8 August 2013
• Misc Tab
  ...other than the Canon or Nikon models the radio is designed for. This mode only uses the center hot shoe contact for sync input and output. It does not use * This setting does not need to match across all radios in use - it needs only be used when connected to a non-compatible camera or flash. For example, tr
  6 KB (944 words) - 10:47, 14 August 2018
• Channels
  ...lus series, MultiMAX, or other PocketWizard radio that performs triggering only and not power control or TTL functions. The Plus and Plus II radios use only Channels 1 through 4. The PlusX uses Channels 1 through 10. The Plus III, P
  18 KB (2,678 words) - 13:09, 26 December 2022
• Getting Started
  #* Continue to hold the Backlight button, and move the power switch to Transmit ...Release is not available for the MultiMAX or MultiMAX II. These radios can only use the Legacy firmware.
  18 KB (2,830 words) - 15:45, 10 February 2024
• Understanding HyperSync and High Speed Sync
  ...r, which means there is less light available for the image, and is usually only available in lower powered Speedlites/Speedlights. Syncing up to 1/8000 is ...s TTL communication both from the camera and to the flash. It is typically only available within a closed manufacturing system, for example, a Nikon camera
  26 KB (4,282 words) - 11:56, 3 January 2021
• Canon Compatibility
  ...mmended to specify your camera model in the [[Misc Tab#Camera Model (Canon Only)|Misc Tab]] of the [[PocketWizard Utility]] for your transmitting radio. :Range limited due to RF interference from flash only when connected to a remote FlexTT5 or FlexTT6. See [[Long Range Performanc
  9 KB (1,478 words) - 08:18, 6 April 2022
• Manual Flash
  ...ving PocketWizard, including flashes with built-in PocketWizards. They can transmit on any of the 32 [[Channels#Standard_Channels|PocketWizard Standard Channel ...n-camera PocketWizard will communicate with the device in its top shoe and transmit power level changes to remote ControlTL receivers automatically.
  2 KB (386 words) - 11:34, 8 June 2017
• Factory Reset
  #While holding C, slide the power switch to TRANSMIT (TRANSMIT and RECEIVE are always reset together). ===Reset A - Reset Channels Only ===
  8 KB (1,270 words) - 09:58, 25 February 2024
• Learn Mode
  ...Standard Channels on the Plus II and MultiMAX can be used for triggering only. ...ly. When being taught from a Standard transmitter it will learn to receive only on a Standard channel. When being taught from a ControlTL transmitter, it
  12 KB (1,773 words) - 13:46, 8 July 2015
• Plus II
  ...an "Auto-Sensing" transceiver which automatically switches from receive to transmit as needed and reliably triggers lights and/or cameras up to 1600 feet away.
  4 KB (553 words) - 10:03, 28 September 2022
• Plus III FAQ
  ...time, they can only receive on one or the other. The default is to receive only on ControlTL Channels. ...box. This will make your FlexTT5/FlexTT6 behave just like a Plus radio and only send and receive on Standard Channels. The ControlTL radios have 2 Configur
  7 KB (1,147 words) - 16:25, 24 October 2021
• MiniTT1 and FlexTT5 Specifications
  |'''Transmit Output Power''' ...>Ring = Pre-Trigger <br>Sleeve = Ground <br> [[Note:]] This port is output only.
  3 KB (482 words) - 07:56, 9 January 2013
• PlusX FAQ
  ...time, they can only receive on one or the other. The default is to receive only on ControlTL Channels. ====What’s Transmit Only Mode? How do I enable it?====
  6 KB (944 words) - 09:55, 28 December 2016
• Relay Mode
  *That radio then automatically switches to transmit mode and waits for the camera to provide a sync pulse. ...a MultiMAX). The radios connected to the flashes can be set to TxRx or Rx Only.
  11 KB (1,947 words) - 08:05, 19 October 2022
• Bandwidth Test
  ...advanced features like TTL and FP/High Speed Sync. Relay Mode with TTL is only available in single shot mode. ...nsmit on ControlTL Channel 2 to trigger flash in sync. You can specify the transmit and receive channels via the PocketWizard Utility.
  6 KB (1,003 words) - 08:28, 7 November 2011
• Plus III
  Plus III Transceivers do not transmit TTL information. You can use a TTL flash directly connected to your camera If you are using a handheld camera to transmit to a remote handheld camera (with Plus IIIs on each camera), we suggest usi
  33 KB (5,538 words) - 19:40, 29 October 2023
• Multiuser Environments
  ...private digital code. In crowded shooting environments, Custom IDs allow only you to trigger your remote flash or camera. Other photographers cannot tr ...adios with USB ports. If you have an original MultiMAX (power and DC ports only) or a MultiMAX with an ACC port but no USB, please contact us at [https://p
  20 KB (3,256 words) - 17:09, 5 April 2022
• PlusX
  ===Transmit Only Mode=== Transmit Only mode allows you to disable the receiver function of the PlusX. Use this mod
  9 KB (1,411 words) - 12:12, 22 November 2022
• Power Control for Non-Compatible Cameras
  ...Remote speedlights must be used with receiving FlexTT5 or FlexTT6 radios. Only compatible Canon/Nikon speedlights are supported and the receiving FlexTT5 * Power control with non-compatible cameras is only possible if the radio brand matches the speedlight brand. For example, you
  3 KB (591 words) - 10:30, 28 April 2021
• MultiMAX FAQ
  ...s instantaneous, it is not. Even the flash, which appears to provide light only for an instant, has a time duration (flash duration) that needs to be facto #Set the MultiMAX to TRANSMIT. When the Unit is in USB mode the LCD screen should be blank, the top red L
  6 KB (982 words) - 09:39, 20 September 2021