Basic Wireless TTL

All references to TTL on this page refer exclusively to Canon's E-TTL II system, or Nikon's i-TTL/CLS. Film TTL or earlier digital TTL systems are not supported.

"Speedlite" and "Speedlight" are used interchangeably. Either may be used to refer to Nikon or Canon's hot shoe flashes. Nikon or Canon specific information will be noted as needed.

REMINDER: Speedlights mounted on a remote FlexTT5 should be set to their standard i-TTL/E-TTL mode. Do not use <MASTER>, <REMOTE> or <SLAVE> modes on a remote flash.

Next recommended reading: Advanced Wireless TTL

This section talks about Basic Wireless TTL where all Speedlights are used as one zone of camera-controlled light and not independently controlled using zones, groups, or ratios. Read Advanced Wireless TTL for independently controlling different groups or zones of TTL flash, or for working with ratios. You may also want to read about Manual Flash.

Make sure you read the Getting Started section first!

No Flash On Camera

This simple mode of operation allows you to use one or more remote TTL flashes as one zone of light. All remote TTL flashes will fire at the same power level which is chosen automatically by the camera.

1. Slide a MiniTT1 Transmitter onto the camera and tighten the locking ring.
2. Slide a remote Speedlite onto a FlexTT5 Transceiver's hot shoe, tighten the locking ring, and secure the FlexTT5. Repeat for each remote Speedlite. The remote Speedlites should be set to normal mode, not <MASTER> or <SLAVE> or <REMOTE>.
3. Power on your equipment from the top down (flash, then radio, then camera).
4. Trigger normally.

Nikon Note

Please read your Nikon manuals on Advanced Wireless Lighting, also called CLS (Creative Lighting System).

This "No Flash On Camera" method is like using Nikon's wireless system with one of the following directly in the shoe of the camera:

• An SU-800 in TTL Commander mode
• An SB-800 or SB-900 as MASTER in Advanced Wireless Lighting TTL Mode with master flash cancelled and a single remote group/zone selected as TTL with 0.0 FEC.

Canon Note

Please read your Canon manuals on Fully Automatic Wireless Flash, also called E-TTL II Wireless Autoflash.

This "No Flash On Camera" method is the same as using Canon’s wireless system with one of the following directly in the shoe of the camera:

• An ST-E2 in non-ratio mode
• A 580EX (I or II) Speedlite in <MASTER> mode, main flash off, in non-ratio mode.

Flash on Camera

This mode is similar to the above, adding a flash on top of the ControlTL radio in the shoe of your camera.

Canon Basic Wireless E-TTL II

This mode is identical to the above, adding a flash to the top hot shoe of the MiniTT1. All remote E-TTL II flashes and the master flash will be treated as one zone of light and will fire at the same power level which is chosen automatically by the camera.

1. Slide the MiniTT1 Transmitter onto the camera and tighten the locking ring.
2. Slide a Canon Speedlite onto the MiniTT1 and secure the Speedlite's locking foot.
   • Force TTL Master Mode is engaged by default. You can use <MASTER> Mode if your flash has it, or you can just place a flash in the radio's hot shoe set to normal ETTL mode.
3. Slide the remote Speedlite onto a FlexTT5 Transceiver, tighten the locking ring, and secure the FlexTT5. Repeat for each remote Speedlite. The remote Speedlites should be set to normal ETTL mode, not <MASTER> or <SLAVE>.
4. Power on your equipment from the top down (flash, then radio, then camera).
5. Trigger normally.

NOTE: You can use a 430EX (I or II) as a master flash! These flashes do not have a master mode, and cannot usually trigger remote E-TTL II flashes. Force TTL Master Mode is engaged by default which gives these flashes the ability to act as a single zone master flash.

Nikon Basic Wireless i-TTL

The Nikon i-TTL system does not have a basic mode where all remote zones and a MASTER flash are treated as a single zone of light. In the Nikon i-TTL/CLS system, the MASTER flash is always treated as its own zone of light separate from remote groups or zones. If you want all of your remote Speedlights to trigger as one zone or group of light, just follow the steps in the Advanced Wireless TTL section and set all of your remote Flex TT5 radios to Zone A.