Difference between revisions of "Manual Flash"
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{recommended reading|HyperSync|}} | + | {{recommended reading|Understanding HyperSync and High Speed Sync|}} |
| − | A transmitting MiniTT1 | + | __TOC__ |
| + | |||
| + | A transmitting MiniTT1, FlexTT5, or FlexTT6 can trigger any receiving PocketWizard, including flashes with built-in PocketWizards. They can transmit on any of the 32 [[Channels#Standard_Channels|PocketWizard Standard Channels]] and a receiving FlexTT5 can be used with [[MultiMAX zones]]. You can even trigger E-TTL and manual flashes together. | ||
| + | |||
| + | |||
| + | ==Remote Manual Flash Control from Camera Position== | ||
| + | |||
| + | You can use a 580EX II, SB-700, SB-800, SB-900, SU-800, or [[AC3 ZoneController]] as a master unit attached to the PocketWizard on your camera to control manual power levels of compatible flashes connected to ControlTL receivers. The on-camera PocketWizard will communicate with the device in its top shoe and transmit power level changes to remote ControlTL receivers automatically. | ||
| + | |||
| + | Note that when using an on-camera Master unit to control remote power levels, leave remote speedlights in their "TTL" mode. As ControlTL radios use the flash's TTL systems to communicate with Speedlights - even when controlling the power manually from camera position - setting the flash to Manual as described in the sections below will ''disable'' power controlling ability from your camera. | ||
| + | |||
[[File:manualspeedlite.jpg|400px|thumb|right|A 580EX II in manual mode.]] | [[File:manualspeedlite.jpg|400px|thumb|right|A 580EX II in manual mode.]] | ||
| − | + | ==Triggering Hot Shoe Flashes Manually== | |
Slide a Speedlite or other manual flash into the top shoe of a FlexTT5 for manual triggering without cords. You can also use a manual flash in the top shoe of an on-camera MiniTT1 or FlexTT5. No configuration of the radio is necessary. | Slide a Speedlite or other manual flash into the top shoe of a FlexTT5 for manual triggering without cords. You can also use a manual flash in the top shoe of an on-camera MiniTT1 or FlexTT5. No configuration of the radio is necessary. | ||
| − | + | ==Triggering Studio Strobes== | |
You can use a receiving FlexTT5 to trigger studio strobes. Use our [http://www.pocketwizard.com/support/cable_finder/ Cable Finder] to find the right cable for lots of different strobes. | You can use a receiving FlexTT5 to trigger studio strobes. Use our [http://www.pocketwizard.com/support/cable_finder/ Cable Finder] to find the right cable for lots of different strobes. | ||
| − | If you’re using a PocketWizard Plus, Plus II, or | + | If you’re using a PocketWizard Plus, [[Plus II]], [[MultiMAX]], or [http://www.sekonic.com/ Sekonic Meter]as a transmitter, be sure to set the FlexTT5 to receive on a Standard Channel via [[Misc_Tab#Basic_Trigger|Basic Trigger Mode]]. This can be set in the [[PocketWizard Utility]], under the [[Misc Tab]] while shooting on-location via Learn Mode. See the tutorial on [[Learn Mode]] here. |
| − | + | ||
| − | + | ||
| − | + | ||
| − | '''Note:''' Do not connect a flash to the camera port (P1) on a FlexTT5. You could damage your radio. This port is for triggering Canon motor drives only and isn’t designed for the trigger voltages used by some flashes. | + | '''Note:''' Do not connect a flash to the camera port (P1) on a FlexTT5 or FlexTT6. You could damage your radio. This port is for triggering Canon motor drives only and isn’t designed for the trigger voltages used by some flashes. |
| − | + | ||
Latest revision as of 10:34, 8 June 2017
| Next recommended reading: Understanding HyperSync and High Speed Sync |
Contents
A transmitting MiniTT1, FlexTT5, or FlexTT6 can trigger any receiving PocketWizard, including flashes with built-in PocketWizards. They can transmit on any of the 32 PocketWizard Standard Channels and a receiving FlexTT5 can be used with MultiMAX zones. You can even trigger E-TTL and manual flashes together.
Remote Manual Flash Control from Camera Position
You can use a 580EX II, SB-700, SB-800, SB-900, SU-800, or AC3 ZoneController as a master unit attached to the PocketWizard on your camera to control manual power levels of compatible flashes connected to ControlTL receivers. The on-camera PocketWizard will communicate with the device in its top shoe and transmit power level changes to remote ControlTL receivers automatically.
Note that when using an on-camera Master unit to control remote power levels, leave remote speedlights in their "TTL" mode. As ControlTL radios use the flash's TTL systems to communicate with Speedlights - even when controlling the power manually from camera position - setting the flash to Manual as described in the sections below will disable power controlling ability from your camera.
Triggering Hot Shoe Flashes Manually
Slide a Speedlite or other manual flash into the top shoe of a FlexTT5 for manual triggering without cords. You can also use a manual flash in the top shoe of an on-camera MiniTT1 or FlexTT5. No configuration of the radio is necessary.
Triggering Studio Strobes
You can use a receiving FlexTT5 to trigger studio strobes. Use our Cable Finder to find the right cable for lots of different strobes.
If you’re using a PocketWizard Plus, Plus II, MultiMAX, or Sekonic Meteras a transmitter, be sure to set the FlexTT5 to receive on a Standard Channel via Basic Trigger Mode. This can be set in the PocketWizard Utility, under the Misc Tab while shooting on-location via Learn Mode. See the tutorial on Learn Mode here.
Note: Do not connect a flash to the camera port (P1) on a FlexTT5 or FlexTT6. You could damage your radio. This port is for triggering Canon motor drives only and isn’t designed for the trigger voltages used by some flashes.
