Difference between revisions of "SpeedCycler"

From PocketWizard Wiki
Jump to: navigation, search
(MultiMAX SpeedCycler)
 
(3 intermediate revisions by the same user not shown)
Line 3: Line 3:
  
 
SpeedCycler requires a [[ControlTL]] radio ([[MiniTT1 and FlexTT5|MiniTT1 or FlexTT5]]) or a [[MultiMAX]] as the transmitter. For [[MultiMAX]] users, Quad Triggering Channels (17  
 
SpeedCycler requires a [[ControlTL]] radio ([[MiniTT1 and FlexTT5|MiniTT1 or FlexTT5]]) or a [[MultiMAX]] as the transmitter. For [[MultiMAX]] users, Quad Triggering Channels (17  
and higher) are required. For [[ControlTL]] users, an [[AC3 ZoneController]] is required. In addition, SpeedCycler requires two or more receiving PocketWizard radios with access to Zones ([[Plus III]], [[MultiMAX]], or [[MiniTT1 and FlexTT5|FlexTT5]].  
+
and higher) are required. For [[ControlTL]] users, an [[AC3 ZoneController]] is required. In addition, SpeedCycler requires two or more receiving PocketWizard radios with access to Zones ([[Plus III]], [[MultiMAX]], or [[MiniTT1 and FlexTT5|FlexTT5]]).  
  
  
Line 11: Line 11:
 
# Enable two or more remote Zones.
 
# Enable two or more remote Zones.
 
# Set each receiving radio to a different Zone.
 
# Set each receiving radio to a different Zone.
# Trigger the [[MultiMAX]] (set for TRANSMIT mode). The first trigger will fire the first Zone selected, the second trigger will fire the next Zone selected. The display indicates  
+
# Trigger the [[MultiMAX]] (set for TRANSMIT mode). The first trigger will fire the first Zone selected, the second trigger will fire the next Zone selected. The display indicates the next Zone to trigger with an arrow. Only the Zone just triggered will display proper confirmation.
the next Zone to trigger with an arrow. Only the Zone just triggered will display proper confirmation.
+
  
  
'''Note:''' If L is selected then PORT 2 on the [[MultiMAX]] (set for TRANSMIT mode) will trigger every time and is not cycled. It will be in sync with each cycled Zone.
+
'''Note:''' If Zone "L" is selected, then a flash plugged into PORT 2 on the transmitting [[MultiMAX]] will trigger every time and is not cycled. It will fire in sync with each cycled Zone as each Zone is triggered in turn.
 
+
  
 
==ControlTL SpeedCycler==
 
==ControlTL SpeedCycler==
Line 25: Line 23:
 
# Apply changes. Once changes have been applied, disconnect your radio.
 
# Apply changes. Once changes have been applied, disconnect your radio.
 
# Set each receiving FlexTT5 to a different Zone.
 
# Set each receiving FlexTT5 to a different Zone.
 +
# Set the Zones on the AC3 to either A or M. (see note below)
 
# Trigger the transmitter. Zones A, B, and C will be triggered sequentially and individual zones can be disabled by setting the AC3's Zone Switch to the off position.
 
# Trigger the transmitter. Zones A, B, and C will be triggered sequentially and individual zones can be disabled by setting the AC3's Zone Switch to the off position.
  
  
 
'''Note:''' SpeedCycler mode requires an AC3 ZoneController in the top shoe of the on-camera PocketWizard radio. Both TTL and manual flash are supported. Setting flash power manually will trigger faster. Receiving [[MultiMAX]]es or [[Plus III]]s can be used instead of FlexTT5s provided a Standard Channel between 17 and 32 is in use. Make sure to set the Standard Transmit Channel on your transmitting [[ControlTL]] radio to match the receiving MultiMAX's or Plus III's. The MultiMAX's and Plus III's A, B, and C Zones correspond to the AC3's Zones.
 
'''Note:''' SpeedCycler mode requires an AC3 ZoneController in the top shoe of the on-camera PocketWizard radio. Both TTL and manual flash are supported. Setting flash power manually will trigger faster. Receiving [[MultiMAX]]es or [[Plus III]]s can be used instead of FlexTT5s provided a Standard Channel between 17 and 32 is in use. Make sure to set the Standard Transmit Channel on your transmitting [[ControlTL]] radio to match the receiving MultiMAX's or Plus III's. The MultiMAX's and Plus III's A, B, and C Zones correspond to the AC3's Zones.

Latest revision as of 08:25, 18 June 2014

SpeedCycler is designed to rapidly cycle through multiple flash units fired individually in sequence. This allows you to fire a camera in sync with flashes faster than a single flash can recycle. It can also be used for triggering remote cameras sequentially.


SpeedCycler requires a ControlTL radio (MiniTT1 or FlexTT5) or a MultiMAX as the transmitter. For MultiMAX users, Quad Triggering Channels (17 and higher) are required. For ControlTL users, an AC3 ZoneController is required. In addition, SpeedCycler requires two or more receiving PocketWizard radios with access to Zones (Plus III, MultiMAX, or FlexTT5).


MultiMAX SpeedCycler

  1. From the main screen press /MENU A D to enable SpeedCycler mode on a MultiMAX (set for TRANSMIT mode).
  2. Enable two or more remote Zones.
  3. Set each receiving radio to a different Zone.
  4. Trigger the MultiMAX (set for TRANSMIT mode). The first trigger will fire the first Zone selected, the second trigger will fire the next Zone selected. The display indicates the next Zone to trigger with an arrow. Only the Zone just triggered will display proper confirmation.


Note: If Zone "L" is selected, then a flash plugged into PORT 2 on the transmitting MultiMAX will trigger every time and is not cycled. It will fire in sync with each cycled Zone as each Zone is triggered in turn.

ControlTL SpeedCycler

  1. Connect your transmitting ControlTL radio to the PocketWizard Utility via USB.
  2. Navigate to the "Misc Tab."
  3. Enable SpeedCycler by clicking the check-box.
  4. Apply changes. Once changes have been applied, disconnect your radio.
  5. Set each receiving FlexTT5 to a different Zone.
  6. Set the Zones on the AC3 to either A or M. (see note below)
  7. Trigger the transmitter. Zones A, B, and C will be triggered sequentially and individual zones can be disabled by setting the AC3's Zone Switch to the off position.


Note: SpeedCycler mode requires an AC3 ZoneController in the top shoe of the on-camera PocketWizard radio. Both TTL and manual flash are supported. Setting flash power manually will trigger faster. Receiving MultiMAXes or Plus IIIs can be used instead of FlexTT5s provided a Standard Channel between 17 and 32 is in use. Make sure to set the Standard Transmit Channel on your transmitting ControlTL radio to match the receiving MultiMAX's or Plus III's. The MultiMAX's and Plus III's A, B, and C Zones correspond to the AC3's Zones.