Difference between revisions of "Relay Mode"

From PocketWizard Wiki
Jump to: navigation, search
(Complete revamp of page, added details for all PW radios and)
(Notes: added info about Auto Relay)
Line 25: Line 25:
  
 
*The radio in your hand can be set to TxRx or Transmit Only. The radio on the camera MUST be set to TxRx. The radios connected to the flashes can be set to TxRx or Rx Only.
 
*The radio in your hand can be set to TxRx or Transmit Only. The radio on the camera MUST be set to TxRx. The radios connected to the flashes can be set to TxRx or Rx Only.
 +
 +
*Relay is automatically engaged if you are using auto sensing PocketWizard transceivers. If you are using Plus III, Plus IV, FlexTT5, or FlexTT6 radios and have a receiving radio in the hot shoe of a remote camera, the radio will automatically relay a signal on the next higher Channel. In most situations, this is not an issue. However, if you are shooting in an environment with multiple PocketWizard users, this may result in your radio sending out unwanted triggers if you are not using a remote flash as well. Please see the Auto Relay section below for details about how to prevent triggering another photographer's PocketWizard units.
  
 
*MultiMAX radios: To set up Relay mode, set the radio to Transmit mode and choose what Channel you wish to use to trigger your flashes (for example, Channel 20). Switch the MultiMAX to Receive mode and choose the Channel you wish to use to receive the original trigger (for example, Channel 17). Press "L" and you will see "RLY 20" on the screen. The MultiMAX will receive a signal on Channel 17 and transmit on Channel 20.
 
*MultiMAX radios: To set up Relay mode, set the radio to Transmit mode and choose what Channel you wish to use to trigger your flashes (for example, Channel 20). Switch the MultiMAX to Receive mode and choose the Channel you wish to use to receive the original trigger (for example, Channel 17). Press "L" and you will see "RLY 20" on the screen. The MultiMAX will receive a signal on Channel 17 and transmit on Channel 20.
Line 33: Line 35:
  
 
*PowerST4 and PowerMC2 receivers can also be used for Relay mode, be sure to adjust the Channels as described.
 
*PowerST4 and PowerMC2 receivers can also be used for Relay mode, be sure to adjust the Channels as described.
 
 
 
  
 
==Custom ID Information==
 
==Custom ID Information==

Revision as of 10:29, 14 October 2019

Next recommended reading: Remote Camera Triggering
Relay.JPG

You can trigger flashes in sync with your remote camera. This is called Relay Mode. You will need at least 3 PocketWizard radios-one in your hand (or on the camera in your hand), one PocketWizard in the camera's hot shoe connected with the appropriate remote camera cable, and a remote Pocketwizard connected to your flash. The transmitting and camera PocketWizards need to be set to the same Channel and the PocketWizards connected to the flashes need to be set to receive one Channel higher.

How Relay Mode Works

  • The PocketWizard in your hand sends a signal to the PocketWizard attached to the camera.
  • The PocketWizard on the remote camera receives the signal and triggers the camera's shutter through the remote camera cable.
  • That radio then automatically switches to transmit mode and waits for the camera to provide a sync pulse.
  • When the shutter moves, the camera sends a signal through the hot shoe to the PocketWizard then the radio will send a trigger to the remote PocketWizards on the next higher Channel.
  • The PocketWizards connected to the flashes will receive the signal the higher Channel and fire the flash in sync with the camera's shutter.

To summarize: Set the radio in your hand and the radio on the camera to the same Channel and set the radio(s) with the remote flash(es) to receive one Channel higher. For example: use Channel 1 for the PocketWizard in your hand and on the camera and use Channel 2 for the PocketWizard(s) connected to the flash(es).

Notes

  • To determine which remote camera cable you need, please see our Cable Finder
  • Be sure the radio connected to the camera is in the hot shoe as well as connected by the remote camera cable.
  • The radio in your hand can be set to TxRx or Transmit Only. The radio on the camera MUST be set to TxRx. The radios connected to the flashes can be set to TxRx or Rx Only.
  • Relay is automatically engaged if you are using auto sensing PocketWizard transceivers. If you are using Plus III, Plus IV, FlexTT5, or FlexTT6 radios and have a receiving radio in the hot shoe of a remote camera, the radio will automatically relay a signal on the next higher Channel. In most situations, this is not an issue. However, if you are shooting in an environment with multiple PocketWizard users, this may result in your radio sending out unwanted triggers if you are not using a remote flash as well. Please see the Auto Relay section below for details about how to prevent triggering another photographer's PocketWizard units.
  • MultiMAX radios: To set up Relay mode, set the radio to Transmit mode and choose what Channel you wish to use to trigger your flashes (for example, Channel 20). Switch the MultiMAX to Receive mode and choose the Channel you wish to use to receive the original trigger (for example, Channel 17). Press "L" and you will see "RLY 20" on the screen. The MultiMAX will receive a signal on Channel 17 and transmit on Channel 20.
  • Half press function: This will still work as described in the Cables page. If you are using 2 Plus IIIs and an older radio, like a Plus II, you can still take advantage of the half press feature. Set the Plus IIIs to Channel 32 and use them as the main trigger and on the camera. Use the Plus II radio(s) for the flash(es), set to Channel 1. The Plus III will "loop" the Channel and receive on Channel 32 but trigger on Channel 1.
  • FlexTT5 / FlexTT6: These radios will auto relay to the next higher Channel but you can choose different Channels to use via the Utility menu. Go to the Channels tab and adjust the transmitting and receiving Channels as you wish.
  • PowerST4 and PowerMC2 receivers can also be used for Relay mode, be sure to adjust the Channels as described.

Custom ID Information

If you have Custom IDs installed on your radios, you can combine Custom ID Channels with regular Channels.

  • MultiMAX: The frequency will not impact the way relay functions. Choose the Channels you wish to use and be sure to note what frequency you are using when you register the radios at an event.
  • Plus III or Plus IV: The radio will auto relay to the next higher Channel. If you have one Custom ID on Channel 17 (for example), it will trigger the remote flash on Standard Channel 18. If you have 2 Custom IDs installed in each radio, on (for example) Channel 18 AND Channel 19, it will trigger the remote flash on Custom ID Channel 19.
  • FlexTT5 or FlexTT6: The radio will auto relay to the next higher Channel like the Plus radios above unless you change it in the Utility. The frequency will not impact the way relay functions.