Difference between revisions of "PowerMC2"

From PocketWizard Wiki
Jump to: navigation, search
(Updating the safety warning)
(major overhaul, moved sections all around)
 
(42 intermediate revisions by 4 users not shown)
Line 1: Line 1:
 +
[[File:PWPOWERMC2.jpg|right|300px]]
 +
 +
The PowerMC2 Receiver Module enables remote power control of Einstein™ E640 flashes using PocketWizard [[ControlTL]] technology. With a Raven by Fusion TLC, [[MiniTT1_and_FlexTT5|a MiniTT1 Transmitter, or a FlexTT5 / FlexTT6 Transceiver]] on your camera and a PowerMC2 plugged into your Einstein™ E640 flash, you can now adjust the flash power settings directly from the camera position. Add the [[AC3 ZoneController]] to your PocketWizard transmitting radios and you can control up to four different Zones of lights in 1/3-stop increments with up to a six-stop range. Utilize PocketWizard’s unique features such as [[HyperSync]] and Optimized [[Rear Curtain Sync]] for maximum control of your lighting.
 +
 +
The PowerMC2 can also be used with any PocketWizard using Standard Channels as well, such as a Plus II or MultiMAX, and it can be triggered by a Sekonic light meter with a PocketWizard module.
 +
 +
==2014 Safety Notice==
 
<div align="left">
 
<div align="left">
 
{| border="1" class="wikitable"
 
{| border="1" class="wikitable"
 
|-
 
|-
|<b>SAFETY NOTICE:</b>
+
|<b>FEBRUARY 2014 SAFETY NOTICE FOR CURRENT POWERMC2 OWNERS:</b>
 +
 
 +
'''NOTE: This message was first sent out in February 2014. If you purchased your PowerMC2 radios after that point, as new units from an authorized dealer or distributor, please [[#PowerMC2 Receiver with ControlTL® for Einstein­™ E640 Flash | click here]] to continue to the PowerMC2 Wiki page.'''
  
We have identified a potentially hazardous issue with the PocketWizard® PowerMC2 receiver when used in combination with the Paul C. Buff Einstein™ E640 flash units, especially the CE/433 MHz version sold in Europe.   You may have received a previous message from Paul C. Buff, Inc. regarding this issue.  
+
We have identified a potentially hazardous issue with the PocketWizard® PowerMC2 receiver when used in combination with the Paul C. Buff Einstein™ E640 flash units, especially the CE/433 MHz version sold in Europe. You may have received a previous message from Paul C. Buff, Inc. regarding this issue.  
  
 
In rare circumstances, if the PowerMC2 is connected to the Einstein flash and the Einstein flash is connected to a power outlet, exposed metal components like the USB port or antenna spring on the PowerMC2 can become electrified, posing a potentially serious shock hazard. If the PowerMC2’s antenna cover is broken, removed, or in any way damaged, DISCONTINUE USE IMMEDIATELY and contact PocketWizard.
 
In rare circumstances, if the PowerMC2 is connected to the Einstein flash and the Einstein flash is connected to a power outlet, exposed metal components like the USB port or antenna spring on the PowerMC2 can become electrified, posing a potentially serious shock hazard. If the PowerMC2’s antenna cover is broken, removed, or in any way damaged, DISCONTINUE USE IMMEDIATELY and contact PocketWizard.
  
Customers in the United States may continue to safely use the Einstein flash and PowerMC2 with the power cord supplied by Paul C. Buff and a properly wired USA-style three-pronged power outlet (NEMA 5) or with the Vagabond battery pack.  If a properly wired NEMA 5 power outlet is unavailable in your location, ALWAYS UNPLUG THE FLASH PRIOR TO HANDLING THE POWERMC2.  
+
Customers in the United States may continue to safely use the Einstein flash and PowerMC2 with the power cord supplied by Paul C. Buff and a properly wired USA-style three-pronged power outlet ([http://en.wikipedia.org/wiki/NEMA_connector#NEMA_5 NEMA 5]) or with the Vagabond battery pack.  If a properly wired NEMA 5 power outlet is unavailable in your location, ALWAYS UNPLUG THE FLASH PRIOR TO HANDLING THE POWERMC2.  
  
The issue has been corrected for all PowerMC2 units sold by PocketWizard’s authorized distributor in the USA after February 15, 2014.  Customers owning affected units are advised to immediately contact PocketWizard Technical Support toll free at +1 877-393-0045 or via our [http://www.pocketwizard.com/contact/inquiry/ inquiry page] to arrange for the return of affected units for free servicing to reduce the risk of electrical shock. We urge you to contact us regardless of the condition of your PowerMC2. We greatly apologize for this inconvenience.  
+
The issue has been corrected for all PowerMC2 units sold by PocketWizard’s authorized distributor in the USA after February 15, 2014.  Customers owning affected units are advised to immediately contact PocketWizard Technical Support at +1 802-318-4456 or via our [https://pocketwizard.com/contact/ inquiry page] to arrange for the return of affected units for free servicing to reduce the risk of electrical shock. We urge you to contact us regardless of the condition of your PowerMC2. We greatly apologize for this inconvenience.  
  
  
Affected units:
+
<b>Affected units:</b>
  
 
*All units with the CE logo on the back, or any serial number beginning M2Cxxxxxxx are affected and correctable.  
 
*All units with the CE logo on the back, or any serial number beginning M2Cxxxxxxx are affected and correctable.  
 +
:[[File:PowerMC2_Affected_CE_label.png|none|left|123px]]
  
 
*Units with the FCC logo on the back and with a serial number M2U192000 or lower are affected and correctable.  
 
*Units with the FCC logo on the back and with a serial number M2U192000 or lower are affected and correctable.  
 +
:[[File:PowerMC2_Affected_FCC_label.png|none|left|123px]]
  
 +
<b>Corrected units:</b>
  
Corrected units:
+
*Units sold by PocketWizard’s authorized distributor in the USA after February 15th, 2014, or have serial number M2U194000 and higher, already have corrective safety features and warnings installed.  Identifying features are “www.pwpatents.com” on the serial number sticker, and/or a yellow warning label.
 
+
:[[File:PowerMC2_Corrected_FCC_label.png|none|left|123px]]
*Units sold by PocketWizard’s authorized distributors in the USA after February 15th, 2014, or have serial number M2U194000 and higher, already have corrective safety features and warnings installed.  Identifying features are “www.pwpatents.com” on the serial number sticker, and a yellow warning label.
+
:[[File:PowerMC2_Warning_Sticker.png|none|left|123px]]
 
|}
 
|}
 
</div>
 
</div>
  
==Receiver with ControlTL® for Einstein­™ E640 Flash==
+
==Setting up your PowerMC2==
  
[[File:PWPOWERMC2.jpg|right|300px]]
+
[[File:PowerMC2Einstein.jpg|right|300px]]
 +
'''1.''' [[Getting Started|Update the firmware]] in your PowerMC2 to the most current version. The PowerMC2 can receive ControlTL, Standard, and E Release Channels. See the [[#Transmitter Compatibility|Transmitter Compatibility]] section below to help determine which firmware version to use, based on your transmitting radio. You can also see the [[PocketWizard Firmware|PocketWizard Firmware]] page for more information about the different firmware protocols available.
  
The PowerMC2 Receiver Module enables remote power control of Einstein™ E640 flashes using PocketWizard [[ControlTL]] technology. With a [[MiniTT1_and_FlexTT5|MiniTT1 Transmitter or FlexTT5 Transceiver]] on your camera and a PowerMC2 plugged into your Einstein™ E640 flash, you can now adjust the flash power settings directly from the camera position. Add the [[AC3 ZoneController]] and you can control three different zones of lights in 1/3-stop increments with up to a six-stop range.  Utilize PocketWizard’s unique features such as [[HyperSync]] and Optimized [[Rear Curtain Sync]] for maximum control of your lighting.
+
'''<span style="color:red;">IMPORTANT NOTE: Do not connect the PowerMC2 to the [[PocketWizard Utility]] via USB while the PowerMC2 is also connected to the Einstein E640 flash. Damage to your PowerMC2, Einstein, or computer's USB port could result. Make sure to disconnect the PowerMC2 from any attached flash first.</span>
{{PowerMC2Wallace}}
+
  
==Special Warning==
+
'''2.''' Connect the PowerMC2 to your Einstein™ E640 Flash via the remote port, then power on the flash.
  
When connecting the PowerMC2 to the [[PocketWizard Utility]], make sure to disconnect the PowerMC2 from any attached flash first.
+
'''3.''' Select the Channel and Zone via the E640’s LCD. Please see the [[#Channels and Zones | Channels and Zones]] section below for details.
  
<span style="color:red;">Do not connect the PowerMC2 to USB while also connected to the Einstein E640 flash.</span> Damage to your PowerMC2, Einstein, or Computer's USB port could result.
+
'''4.''' Use the Einstein's function and adjust buttons to disable the Einstein's optical flash. This is the box directly above the Channel box. You should see 2 downward arrows.
  
==Using your PowerMC2==
+
'''4.''' Set up your transmitting radio and take pictures normally.
  
[[File:PowerMC2Einstein.jpg|right|300px]]
+
'''5.''' If your transmitting radio has power control, you can use the camera’s Flash Exposure Compensation (FEC) to adjust power levels globally to all remote flashes. You may also be able to use the transmitting radio and/or AC3/master controller to adjust power to your remote flash(es) by Zone. See the [[#PowerMC2|Power Control]] section for more information.
'''1.''' Connect the PowerMC2 to your Einstein™ E640 Flash via the remote port, then power on the flash.
+
  
'''2.''' Select the Channel and Zone A, B, or C via the E640’s LCD.
+
The Status LED blinks '''<span style="color:green;">Green</span>''' every few seconds to indicate normal operation. It will blink '''<span style="color:red;">Red</span>''' in sync with a trigger.  
  
'''3.''' Set up your PocketWizard transmitter and take pictures normally.  
+
Momentarily pressing TEST on the transmitting radio and/or pressing down on the LED on the PowerMC2 will also trigger the flash.
  
'''4.''' Adjust the camera’s Flash Exposure Compensation (FEC) to adjust the power of your remote flash. See the [[#Basic Power Control|Basic Power Control]] section for more information about FEC.
+
==HyperSync and SyncView==
  
 +
===== [[HyperSync]] with PocketWizard Transmitters =====
 +
[[File:Hypersync.jpg|right]]
 +
Most studio strobes can only sync up to your camera's sync speed - about 1/200 or 1/250 for most current DSLR cameras. Our patented HyperSync® technology allows photographers to achieve faster flash sync speeds. Unlike HSS that uses a pulsing flash with lower power, HyperSync uses your flash's full power burst. That extra speed and light can be used to freeze action or cut ambient light - both of which can produce results never possible before. All you need is a MiniTT1, FlexTT5, or FlexTT6 on your camera to gain the benefits of HyperSync. While performance varies by the camera and flash equipment being used, HyperSync will get the maximum possible out of any configuration.
  
'''Make sure all your radios are set to the same PocketWizard [[Channels|channel]].'''
+
Please see the [[HyperSync Setup|HyperSync Setup]] for details about using HyperSync with ControlTL radios.
 
+
The Status LED blinks '''<span style="color:green;">Green</span>''' every few seconds to indicate normal operation. It will blink '''<span style="color:red;">Red</span>''' in sync with a trigger.  
+
  
Momentarily pressing TEST will test trigger the flash.
+
=====SyncView with the Raven by Fusion TLC=====
  
Your PowerMC2 needs to be on the same channel as your transmitter. [[Channels]] can be set via the Einstein’s built-in LCD. The PowerMC2 is capable of receiving on either ControlTL Channels for use with ControlTL radios like the MiniTT1 and FlexTT5 or [[Channels#Standard_Channels|Standard Channels]] for triggering with the [[Plus II]], [[MultiMAX]], and [[Sekonic]] meters.  
+
The Raven takes PocketWizard's HyperSync technology to a new level. With the push of a button, the SyncView screen displays a never-before-seen representation of flash intensity over the length of the shutter cycle. A built-in light meter captures the flash profile and reveals timing in relation to the opening and closing of the shutter curtains. To adjust flash timing, simply rotate the ring dial to optimize timing of your flash. [https://www.youtube.com/watch?v=QqBi3Gk5nzY This link] illustrates how easy it is to push your shutter speeds to their limits.
  
To set the channel, press the Einstein’s™ FUNCTION button until the Channel selection box is highlighted, and then change channels with the ADJUST buttons. Press the FUNCTION button again to specify a zone. When using ControlTL Channels, or Standard Channels 17-32, you can specify zone A, B, or C.
+
Please see the [https://fusiontlc.com/pages/using-syncview Fusion TLC website] for details about using SyncView.
  
'''Note:''' When receiving on Standard Channels, the PowerMC2 will be unable to do any form of PowerTracking, or remote Manual Power Control. You must be using a ControlTL radio in ControlTL radio mode for the Einstein to be able to engage in any form of ControlTL feature.
+
==Power Control==
  
----
+
The PowerMC2 gives you the ability to adjust power to your Einstein flash from your camera's position, instead of having to adjust power on the Einstein itself. If you are using multiple remote flashes, you can assign each remote flash to a Zone and adjust the power of individual Zones as well. You can have as many remotes assigned to each Zone as you would like.
===== [[PowerMC2 FAQ]] =====
+
Having trouble with your PowerMC2? Check out our [[PowerMC2 FAQ]] page!
+
  
===== [[ControlTL]] =====
+
NOTE: Specific Power Control functions are based on the features of your transmitting radio.  
[[File:controltl.jpg|right]]
+
PocketWizard’s newest firmware platform taps into the camera’s digital communications to enable an entirely new level of remote flash capability through our proven radio system.  ControlTL allows remote [[Basic Wireless TTL|TTL]] systems as well as Manual Power Control.  ControlTL firmware is configurable and [[PocketWizard Utility|upgradeable]] for “future-proof” continuous improvement.
+
  
 
===== Manual Power Control =====
 
===== Manual Power Control =====
 
[[File:manual_power_control.jpg|right]]
 
[[File:manual_power_control.jpg|right]]
Adjust the manual power settings of your remote Einstein flash directly from a [[AC3 ZoneController]], or master flash mounted on your on-camera [[MiniTT1_and_FlexTT5|MiniTT1 or FlexTT5]].  You can independently control the power output of up to three remote groups of lights (you can have as many lights in each group as you want) from full power down to the lowest setting through the user interface on the back of the master flash or with the dials of the AC3 ZoneController.  Now you can work with total control with your remote lights, without leaving your shooting position.
+
You can adjust manual power to the remote flashes globally by using the camera's Flash Exposure Compensation (FEC).
  
===== [[HyperSync]] =====
+
If you are using the Raven or have a master controller on your transmitting MiniTT1, FlexTT5, or FlexTT6, you can adjust manual power to each remote Zone independently. The Einstein does not have TTL.
[[File:Hypersync.jpg|right]]
+
*If you are using a Raven, simply activate the Zone and use the dial to adjust power in manual mode. With PowerMC2 firmware update 4.216 or higher, manual power control is available in Zones A, B, C, and D.
Our patent pending HyperSync® technology allows photographers to achieve faster X-sync speeds with full power flash. That extra speed can be used to freeze action or cut ambient light - both of which can produce results never possible before. HyperSync works automatically with the PowerMC2. All you need is a MiniTT1 or FlexTT5 on camera to gain the benefits of HyperSync. While performance varies by the camera and flash equipment being used, HyperSync will get the maximum possible out of any configuration.
+
*If you are using a MiniTT1, FlexTT5, or FlexTT6, adjust the manual power settings of your remote Einstein flash directly from a [[AC3 ZoneController]], master flash, or master controller (such as the Nikon SU-800 or Canon ST-E3-RT) mounted on your transmitting radio. Manual power control is available in Zones A, B, and C.
 +
 
 +
Now you can work with total control with your remote lights, without leaving your shooting position. Please see the chart below for corresponding power levels.
  
 
===== [[PowerTracking]] =====
 
===== [[PowerTracking]] =====
 
[[File:powertracking.jpg|right]]
 
[[File:powertracking.jpg|right]]
When working with certain manual flashes, you can change any of your settings on your camera and the system adjusts for those settings. Change your camera's exposure compensation to adjust the flash output, or make adjustments in aperture or ISO and the system balances your flash for proper exposure.
+
With PowerTracking, you can pick the perfect light level and lock it in, then when you change any of your settings on your camera, the system adjusts for those settings and will automatically adjust flash power to give you the same exposure. Change your camera's exposure compensation to adjust the flash output, or make adjustments in aperture or ISO and the system balances your flash for proper exposure.
 
+
  
 
''Note that Flash Exposure Compensation can also be dialed in on a per-flash basis, by changing the PowerMC2's settings in the [[Exposure Tab]] of the [[PocketWizard Utility]].''
 
''Note that Flash Exposure Compensation can also be dialed in on a per-flash basis, by changing the PowerMC2's settings in the [[Exposure Tab]] of the [[PocketWizard Utility]].''
 +
 +
For details about PowerTracking with PocketWizard ControlTL radios, please see the [[PowerTracking|PowerTracking]] Wiki page. For details about PowerTracking with the Raven, please see the [https://fusiontlc.com/pages/ttl-manual-and-powertrack Fusion TLC website].
  
 
====[[PowerTracking#Basic Power Control|Basic Power Control]]====
 
====[[PowerTracking#Basic Power Control|Basic Power Control]]====
  
With only a MiniTT1 or FlexTT5 on your camera, your camera’s FEC (Flash Exposure Compensation) control will adjust your flash power output level for all your PowerMC2-connected flashes as shown in the table below.
+
With only a MiniTT1, FlexTT5, or FlexTT6 on your camera, your camera’s FEC (Flash Exposure Compensation) control will adjust your flash power output level for all your PowerMC2-connected flashes as shown in the table below.
  
 
<div align="center">
 
<div align="center">
Line 155: Line 166:
 
</div>
 
</div>
  
====Specifications====
+
==Transmitter Compatibility==
 +
 
 +
The PowerMC2 can be used with any transmitting PocketWizard radio as well as the Raven by Fusion TLC, when connected to the Paul C Buff Einstein. It can also be used with the Paul C Buff LINK when using a Raven as the transmitter. PocketWizard has 2 different firmware protocols, the E Release and Legacy. Please see [[PocketWizard Firmware | this link]] for details about the firmware. Depending on which transmitting units you are using, you may need to upgrade your PowerMC2 to the E Release or downgrade to Legacy.
 +
'''NOTE: It is important to use the most updated version of firmware on all of your products. This includes the PowerMC2, your transmitting radio, the strobes, and your camera.'''
 +
 
 +
 
 +
===Raven by Fusion TLC:===
 +
The PowerMC2 is fully compatible with the Raven, using the E Release firmware and can be used for regular shooting up to X-sync as well as faster sync speeds. You can also adjust power to the Einstein or the LINK from the transmitting Raven. The Einstein is not capable of HSS but you can use [[https://www.youtube.com/watch?v=QqBi3Gk5nzY | SyncView]] to shoot over X-sync. You can use the PowerMC2 with the LINK for both SyncView and HSS. When using E Release firmware with the PowerMC2, the Channels on the Einstein will be displayed as "CH-E 01".
 +
 
 +
Firmware: As of October 2022, the PowerMC2 should be updated to firmware 4.216 or higher and the Einstein needs to be updated to v55 for use with the Raven, which should also have the most updated firmware as well. The LINK needs to be updated to v001.010.101
 +
 
 +
===PocketWizard MiniTT1, FlexTT5, or FlexTT6 with Legacy firmware===
 +
The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync as well as [[HyperSync | HyperSync]]. The Einstein is not capable of HSS. If you use an AC3 ZoneController or other master controller (such as a Nikon or Canon flash with master mode, a Nikon SU-800, or a Canon ST-E2 or ST-E3-RT), you can adjust power to the Einstein from the camera position. When using Legacy firmware with ControlTL radios, be sure to use the CTL Channels on the Einstein. It will be displayed as "CTL 01".
 +
 
 +
===PocketWizard FlexTT5 or FlexTT6 with E Release firmware===
 +
The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync as well as [[HyperSync | HyperSync]]. The PowerMC2 is not capable of HSS. If you use an AC3 ZoneController or other master controller (such as a Nikon or Canon flash with master mode, a Nikon SU-800, or a Canon ST-E2 or ST-E3-RT), you can adjust power to the Einstein from the camera position. When using E Release firmware with the PowerMC2, the Channels on the Einstein will be displayed as "CH-E 01".
 +
 
 +
===PocketWizard Plus III/IIIe or Plus IV/IVe with E Release firmware===
 +
The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync. The Plus radios cannot be used for HSS or HyperSync. You can enable or disable Zones from your transmitting radio but they cannot be used adjust power to the Einsteins. When using E Release firmware with the PowerMC2, the Channels on the Einstein will be displayed as "CH-E 01".
 +
 
 +
===PocketWizard Plus or MultiMAX with Legacy firmware===
 +
The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync. The Plus radios cannot be used for HSS or HyperSync. If using radios with Channel 17 or higher, you can enable or disable Zones from your transmitting radio but they cannot be used adjust power to the Einsteins. When using Legacy firmware with Plus radios and the PowerMC2, the Channels on the Einstein will be displayed as "CH 01".
 +
 
 +
==Channels and Zones==
 +
Your PowerMC2 needs to be on the same Channel as your transmitter. Channels can be set via the Einstein’s built-in LCD. The PowerMC2 is capable of receiving on ControlTL Channels (CTL) and Standard Channels (CH). If the PowerMC2 has been upgraded to the E Release, it can also receive signals on E Release Channels (CH-E).
 +
 
 +
To set the channel, press the Einstein’s™ function button until the Channel selection box is highlighted, and then scroll up or down with the adjust buttons to select the Channel you want. Once your Channel is set, press the function button again and use the adjust buttons to specify a Zone if applicable.
 +
 
 +
'''PocketWizard Standard Channels (for example, using a Plus, MultiMAX, or Sekonic light meter as the transmitter with Legacy firmware)'''
 +
 
 +
*Available Standard Channels CH01 - CH32.
 +
*Channels 17-32 will also have Zones A, B, C, and D. Zones are not available for Channels 1-16.
 +
*You can enable or disable a Zone from a master controller if using Channels 17-32.
 +
*Power Control is not available with Standard Channels.
 +
 
 +
'''PocketWizard ControlTL Channels (for example, using PocketWizard ControlTL radio or Sekonic light meter as the transmitter with Legacy firmware)'''
 +
 
 +
*Available ControlTL Channels CTL01 - CTL20.
 +
*All Channels will have Zones A, B, and C.
 +
*Power Control is available with ControlTL Channels.
 +
 
 +
'''PocketWizard E Release Channels (using PocketWizards that have been upgraded to the E Release or the Raven as the transmitter)''' 
 +
 
 +
*Available E Channels CH-E 01 - CH-E 32. NOTE: Channels 21-32 are only available with PowerMC2 firmware update version 4.216 or higher.
 +
*All Channels will have Zones A, B, and C. Zone D is also available if the PowerMC2 has been updated to firmware 4.216.
 +
*Power Control is available with E Release Channels if the transmitting radio has the ability to send power levels.
 +
 
 +
== [[PowerMC2 FAQ]] ==
 +
Having trouble with your PowerMC2 or do you have questions? Check out our [[PowerMC2 FAQ]] page!
 +
 
 +
==Specifications==
  
 
<div align="center">
 
<div align="center">
Line 164: Line 225:
 
|-
 
|-
 
|'''Channels'''
 
|'''Channels'''
|52 Channels over 26 Frequencies - US FCC/IC <br> 35 Channels over 5 Frequencies - CE
+
|84 Channels over 58 Frequencies - US FCC/IC <br> 35 Channels over 5 Frequencies - CE
 
|-
 
|-
 
|'''Antenna'''
 
|'''Antenna'''
Line 172: Line 233:
 
|Eight-pin remote socket
 
|Eight-pin remote socket
 
|-
 
|-
|'''Zone Select Switch'''
+
|'''Zone Select Options'''
|A-B-C Plus channel "D" if receiving on a MultiMAX channel.
+
|A-B-C or A-B-C-D, depending on Channel and firmware version
 
|-
 
|-
 
|'''Status Indicator'''
 
|'''Status Indicator'''
Line 201: Line 262:
 
|-
 
|-
 
|'''Requirements'''
 
|'''Requirements'''
|Must be used in conjunction with a MiniTT1 or FlexTT5 on camera for power control capability.<br>May be paired with any PocketWizard transmitter or transceiver for simple triggering.
+
|Must be used in conjunction with a MiniTT1, FlexTT5, FlexTT6 or Raven on camera for power control capability.<br>May be paired with any PocketWizard transmitter or transceiver for simple triggering. Also compatible with Sekonic light meters with PocketWizard module.
 
|}
 
|}
 
</div>
 
</div>

Latest revision as of 10:52, 9 October 2022

PWPOWERMC2.jpg

The PowerMC2 Receiver Module enables remote power control of Einstein™ E640 flashes using PocketWizard ControlTL technology. With a Raven by Fusion TLC, a MiniTT1 Transmitter, or a FlexTT5 / FlexTT6 Transceiver on your camera and a PowerMC2 plugged into your Einstein™ E640 flash, you can now adjust the flash power settings directly from the camera position. Add the AC3 ZoneController to your PocketWizard transmitting radios and you can control up to four different Zones of lights in 1/3-stop increments with up to a six-stop range. Utilize PocketWizard’s unique features such as HyperSync and Optimized Rear Curtain Sync for maximum control of your lighting.

The PowerMC2 can also be used with any PocketWizard using Standard Channels as well, such as a Plus II or MultiMAX, and it can be triggered by a Sekonic light meter with a PocketWizard module.

2014 Safety Notice

FEBRUARY 2014 SAFETY NOTICE FOR CURRENT POWERMC2 OWNERS:

NOTE: This message was first sent out in February 2014. If you purchased your PowerMC2 radios after that point, as new units from an authorized dealer or distributor, please click here to continue to the PowerMC2 Wiki page.

We have identified a potentially hazardous issue with the PocketWizard® PowerMC2 receiver when used in combination with the Paul C. Buff Einstein™ E640 flash units, especially the CE/433 MHz version sold in Europe. You may have received a previous message from Paul C. Buff, Inc. regarding this issue.

In rare circumstances, if the PowerMC2 is connected to the Einstein flash and the Einstein flash is connected to a power outlet, exposed metal components like the USB port or antenna spring on the PowerMC2 can become electrified, posing a potentially serious shock hazard. If the PowerMC2’s antenna cover is broken, removed, or in any way damaged, DISCONTINUE USE IMMEDIATELY and contact PocketWizard.

Customers in the United States may continue to safely use the Einstein flash and PowerMC2 with the power cord supplied by Paul C. Buff and a properly wired USA-style three-pronged power outlet (NEMA 5) or with the Vagabond battery pack. If a properly wired NEMA 5 power outlet is unavailable in your location, ALWAYS UNPLUG THE FLASH PRIOR TO HANDLING THE POWERMC2.

The issue has been corrected for all PowerMC2 units sold by PocketWizard’s authorized distributor in the USA after February 15, 2014. Customers owning affected units are advised to immediately contact PocketWizard Technical Support at +1 802-318-4456 or via our inquiry page to arrange for the return of affected units for free servicing to reduce the risk of electrical shock. We urge you to contact us regardless of the condition of your PowerMC2. We greatly apologize for this inconvenience.


Affected units:

  • All units with the CE logo on the back, or any serial number beginning M2Cxxxxxxx are affected and correctable.
PowerMC2 Affected CE label.png
  • Units with the FCC logo on the back and with a serial number M2U192000 or lower are affected and correctable.
PowerMC2 Affected FCC label.png

Corrected units:

  • Units sold by PocketWizard’s authorized distributor in the USA after February 15th, 2014, or have serial number M2U194000 and higher, already have corrective safety features and warnings installed. Identifying features are “www.pwpatents.com” on the serial number sticker, and/or a yellow warning label.
PowerMC2 Corrected FCC label.png
PowerMC2 Warning Sticker.png

Setting up your PowerMC2

PowerMC2Einstein.jpg

1. Update the firmware in your PowerMC2 to the most current version. The PowerMC2 can receive ControlTL, Standard, and E Release Channels. See the Transmitter Compatibility section below to help determine which firmware version to use, based on your transmitting radio. You can also see the PocketWizard Firmware page for more information about the different firmware protocols available.

IMPORTANT NOTE: Do not connect the PowerMC2 to the PocketWizard Utility via USB while the PowerMC2 is also connected to the Einstein E640 flash. Damage to your PowerMC2, Einstein, or computer's USB port could result. Make sure to disconnect the PowerMC2 from any attached flash first.

2. Connect the PowerMC2 to your Einstein™ E640 Flash via the remote port, then power on the flash.

3. Select the Channel and Zone via the E640’s LCD. Please see the Channels and Zones section below for details.

4. Use the Einstein's function and adjust buttons to disable the Einstein's optical flash. This is the box directly above the Channel box. You should see 2 downward arrows.

4. Set up your transmitting radio and take pictures normally.

5. If your transmitting radio has power control, you can use the camera’s Flash Exposure Compensation (FEC) to adjust power levels globally to all remote flashes. You may also be able to use the transmitting radio and/or AC3/master controller to adjust power to your remote flash(es) by Zone. See the Power Control section for more information.

The Status LED blinks Green every few seconds to indicate normal operation. It will blink Red in sync with a trigger.

Momentarily pressing TEST on the transmitting radio and/or pressing down on the LED on the PowerMC2 will also trigger the flash.

HyperSync and SyncView

HyperSync with PocketWizard Transmitters
Hypersync.jpg

Most studio strobes can only sync up to your camera's sync speed - about 1/200 or 1/250 for most current DSLR cameras. Our patented HyperSync® technology allows photographers to achieve faster flash sync speeds. Unlike HSS that uses a pulsing flash with lower power, HyperSync uses your flash's full power burst. That extra speed and light can be used to freeze action or cut ambient light - both of which can produce results never possible before. All you need is a MiniTT1, FlexTT5, or FlexTT6 on your camera to gain the benefits of HyperSync. While performance varies by the camera and flash equipment being used, HyperSync will get the maximum possible out of any configuration.

Please see the HyperSync Setup for details about using HyperSync with ControlTL radios.

SyncView with the Raven by Fusion TLC

The Raven takes PocketWizard's HyperSync technology to a new level. With the push of a button, the SyncView screen displays a never-before-seen representation of flash intensity over the length of the shutter cycle. A built-in light meter captures the flash profile and reveals timing in relation to the opening and closing of the shutter curtains. To adjust flash timing, simply rotate the ring dial to optimize timing of your flash. This link illustrates how easy it is to push your shutter speeds to their limits.

Please see the Fusion TLC website for details about using SyncView.

Power Control

The PowerMC2 gives you the ability to adjust power to your Einstein flash from your camera's position, instead of having to adjust power on the Einstein itself. If you are using multiple remote flashes, you can assign each remote flash to a Zone and adjust the power of individual Zones as well. You can have as many remotes assigned to each Zone as you would like.

NOTE: Specific Power Control functions are based on the features of your transmitting radio.

Manual Power Control
Manual power control.jpg

You can adjust manual power to the remote flashes globally by using the camera's Flash Exposure Compensation (FEC).

If you are using the Raven or have a master controller on your transmitting MiniTT1, FlexTT5, or FlexTT6, you can adjust manual power to each remote Zone independently. The Einstein does not have TTL.

  • If you are using a Raven, simply activate the Zone and use the dial to adjust power in manual mode. With PowerMC2 firmware update 4.216 or higher, manual power control is available in Zones A, B, C, and D.
  • If you are using a MiniTT1, FlexTT5, or FlexTT6, adjust the manual power settings of your remote Einstein flash directly from a AC3 ZoneController, master flash, or master controller (such as the Nikon SU-800 or Canon ST-E3-RT) mounted on your transmitting radio. Manual power control is available in Zones A, B, and C.

Now you can work with total control with your remote lights, without leaving your shooting position. Please see the chart below for corresponding power levels.

PowerTracking
Powertracking.jpg

With PowerTracking, you can pick the perfect light level and lock it in, then when you change any of your settings on your camera, the system adjusts for those settings and will automatically adjust flash power to give you the same exposure. Change your camera's exposure compensation to adjust the flash output, or make adjustments in aperture or ISO and the system balances your flash for proper exposure.

Note that Flash Exposure Compensation can also be dialed in on a per-flash basis, by changing the PowerMC2's settings in the Exposure Tab of the PocketWizard Utility.

For details about PowerTracking with PocketWizard ControlTL radios, please see the PowerTracking Wiki page. For details about PowerTracking with the Raven, please see the Fusion TLC website.

Basic Power Control

With only a MiniTT1, FlexTT5, or FlexTT6 on your camera, your camera’s FEC (Flash Exposure Compensation) control will adjust your flash power output level for all your PowerMC2-connected flashes as shown in the table below.

Camera FEC/EC
- or -
AC3 Power Dial in Manual
Einstein E640 Power Output
+3 1/1
+2.7 1/2 + 0.6
+2.3 1/2 + 0.3
+2 1/2
+1.7 1/4 + 0.6
+1.3 1/4 + 0.3
+1 1/4
+0.7 1/8 + 0.6
+0.3 1/8 + 0.6
0 1/8
-0.3 1/16 + 0.6
-0.7 1/16 + 0.3
-1 1/16
-1.3 1/32 + 0.6
-1.7 1/32 + 0.3
-2 1/32
-2.3 1/64 + 0.6
-2.7 1/64 + 0.3
-3 1/64

Transmitter Compatibility

The PowerMC2 can be used with any transmitting PocketWizard radio as well as the Raven by Fusion TLC, when connected to the Paul C Buff Einstein. It can also be used with the Paul C Buff LINK when using a Raven as the transmitter. PocketWizard has 2 different firmware protocols, the E Release and Legacy. Please see this link for details about the firmware. Depending on which transmitting units you are using, you may need to upgrade your PowerMC2 to the E Release or downgrade to Legacy. NOTE: It is important to use the most updated version of firmware on all of your products. This includes the PowerMC2, your transmitting radio, the strobes, and your camera.


Raven by Fusion TLC:

The PowerMC2 is fully compatible with the Raven, using the E Release firmware and can be used for regular shooting up to X-sync as well as faster sync speeds. You can also adjust power to the Einstein or the LINK from the transmitting Raven. The Einstein is not capable of HSS but you can use [| SyncView] to shoot over X-sync. You can use the PowerMC2 with the LINK for both SyncView and HSS. When using E Release firmware with the PowerMC2, the Channels on the Einstein will be displayed as "CH-E 01".

Firmware: As of October 2022, the PowerMC2 should be updated to firmware 4.216 or higher and the Einstein needs to be updated to v55 for use with the Raven, which should also have the most updated firmware as well. The LINK needs to be updated to v001.010.101

PocketWizard MiniTT1, FlexTT5, or FlexTT6 with Legacy firmware

The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync as well as HyperSync. The Einstein is not capable of HSS. If you use an AC3 ZoneController or other master controller (such as a Nikon or Canon flash with master mode, a Nikon SU-800, or a Canon ST-E2 or ST-E3-RT), you can adjust power to the Einstein from the camera position. When using Legacy firmware with ControlTL radios, be sure to use the CTL Channels on the Einstein. It will be displayed as "CTL 01".

PocketWizard FlexTT5 or FlexTT6 with E Release firmware

The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync as well as HyperSync. The PowerMC2 is not capable of HSS. If you use an AC3 ZoneController or other master controller (such as a Nikon or Canon flash with master mode, a Nikon SU-800, or a Canon ST-E2 or ST-E3-RT), you can adjust power to the Einstein from the camera position. When using E Release firmware with the PowerMC2, the Channels on the Einstein will be displayed as "CH-E 01".

PocketWizard Plus III/IIIe or Plus IV/IVe with E Release firmware

The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync. The Plus radios cannot be used for HSS or HyperSync. You can enable or disable Zones from your transmitting radio but they cannot be used adjust power to the Einsteins. When using E Release firmware with the PowerMC2, the Channels on the Einstein will be displayed as "CH-E 01".

PocketWizard Plus or MultiMAX with Legacy firmware

The PowerMC2 is fully compatible with these radios and can be used for regular shooting up to X-sync. The Plus radios cannot be used for HSS or HyperSync. If using radios with Channel 17 or higher, you can enable or disable Zones from your transmitting radio but they cannot be used adjust power to the Einsteins. When using Legacy firmware with Plus radios and the PowerMC2, the Channels on the Einstein will be displayed as "CH 01".

Channels and Zones

Your PowerMC2 needs to be on the same Channel as your transmitter. Channels can be set via the Einstein’s built-in LCD. The PowerMC2 is capable of receiving on ControlTL Channels (CTL) and Standard Channels (CH). If the PowerMC2 has been upgraded to the E Release, it can also receive signals on E Release Channels (CH-E).

To set the channel, press the Einstein’s™ function button until the Channel selection box is highlighted, and then scroll up or down with the adjust buttons to select the Channel you want. Once your Channel is set, press the function button again and use the adjust buttons to specify a Zone if applicable.

PocketWizard Standard Channels (for example, using a Plus, MultiMAX, or Sekonic light meter as the transmitter with Legacy firmware)

  • Available Standard Channels CH01 - CH32.
  • Channels 17-32 will also have Zones A, B, C, and D. Zones are not available for Channels 1-16.
  • You can enable or disable a Zone from a master controller if using Channels 17-32.
  • Power Control is not available with Standard Channels.

PocketWizard ControlTL Channels (for example, using PocketWizard ControlTL radio or Sekonic light meter as the transmitter with Legacy firmware)

  • Available ControlTL Channels CTL01 - CTL20.
  • All Channels will have Zones A, B, and C.
  • Power Control is available with ControlTL Channels.

PocketWizard E Release Channels (using PocketWizards that have been upgraded to the E Release or the Raven as the transmitter)

  • Available E Channels CH-E 01 - CH-E 32. NOTE: Channels 21-32 are only available with PowerMC2 firmware update version 4.216 or higher.
  • All Channels will have Zones A, B, and C. Zone D is also available if the PowerMC2 has been updated to firmware 4.216.
  • Power Control is available with E Release Channels if the transmitting radio has the ability to send power levels.

PowerMC2 FAQ

Having trouble with your PowerMC2 or do you have questions? Check out our PowerMC2 FAQ page!

Specifications

Frequency 340.00 - 354.00 US FCC/IC
433.42 - 434.42 MHz - CE
Channels 84 Channels over 58 Frequencies - US FCC/IC
35 Channels over 5 Frequencies - CE
Antenna 2.7" (6.9 cm) rubberized
Mounting Eight-pin remote socket
Zone Select Options A-B-C or A-B-C-D, depending on Channel and firmware version
Status Indicator LED: Green, Amber, Red Status indications
USB USB Compliant 2.0, Mini-B Connector, 5VDC regulated, 100mA, Pin 1 Positive, Pin 4 Ground

DO NOT CONNECT RADIO TO USB WHILE ALSO CONNECTED TO EINSTEIN FLASH.

Operating Temperature Above -15° C (5° F) and below 50° C (120° F)
Storage Temperature Above -30° C (22° F) and below 85° C (185° F)
Construction high impact plastic, rubberized antenna, RoHS Compliant
Power Receives power from attached flash
Dimensions 4.66" (11.84 cm) long x 1.29" (3.27 cm) wide x .43" (1.09 cm) depth
Weight .77 ounces (21.83 grams)
Requirements Must be used in conjunction with a MiniTT1, FlexTT5, FlexTT6 or Raven on camera for power control capability.
May be paired with any PocketWizard transmitter or transceiver for simple triggering. Also compatible with Sekonic light meters with PocketWizard module.