PocketWizard Utility FAQ

From PocketWizard Wiki
Revision as of 09:08, 13 May 2016 by Patrick (Talk | contribs) (Why won’t the Utility recognize my radios?)

Jump to: navigation, search


Do you have questions about the PocketWizard Utility? Check out these Frequently Asked Questions, compiled by PocketWizard tech support.


How do I reset everything back to defaults?

ControlTL radios can be reset using the PocketWizard Utility, or by hand in the field. Check out our Factory Reset page for details.


Why won’t the Utility recognize my radios?

This can occur for several reasons. Try the following:

  • Install the latest version of the Utility, available for download on our Getting Started page
  • Try performing a "hard" Factory Reset or "Reset B" on your radio. This can sometimes be effective where clicking the Factory Reset button in the Utility is not
  • If you are using a USB hub, like in your monitor, try a USB port directly on the computer
  • If you are using a USB port directly on the computer, try going through a hub
  • If you are using a USB 3.0 port, try a USB2.0 port, or vice versa
  • Try a different USB cable
  • Make sure your computer's motherboard and operating system drivers are up to date
  • If the radio has batteries in it, try connecting without batteries installed or with brand new batteries
  • If the radio switch is in the OFF position when connecting it to USB, try it in the ON position, or vice versa
  • Try connecting your radio to the computer's USB port before running the PocketWizard Utility
  • Be patient. When disconnecting one radio, wait 15 seconds (or more!) before connecting another one, and then wait up to 2 minutes to see if it eventually connects (it can take a Windows computer up to 2 minutes to recognize a radio for the first time)
  • Wait for any messages in the bottom of the Utility to disappear before connecting another radio, especially "Lost communication..."
  • Temporarily disable any software that is specifically looking for other USB devices, like a voice recorder, camcorder, tablet, gaming controllers, etc.
  • Temporarily disable any anti-virus or anti-malware software that may be trying to "manage" your USB ports for you
  • Disconnect any and all other USB devices that may be interfering
  • Try using a different user account
  • Try using your computer’s Safe Mode
  • Try another computer
  • If you’re still having trouble, contact PocketWizard tech support for help

Can I leave my radio connected to the USB port to test changes quickly?

No. This will affect sync timing. You should disconnect the radio and power cycle it (if it was turned on) after any changes.


Why won’t the Utility let me download the latest firmware version?

Make sure you’re running the latest version of the PocketWizard Utility, which is available for download on our Getting Started page.


Are you looking for Beta Firmware? Make sure you've enabled that in the PocketWizard Utility. Follow the steps here.


The Utility uses the standard FTP protocol to download firmware files. Make sure your computer's firewall, internet router, or internet service provider (ISP) are not blocking FTP. You can test FTP by entering the following URL into your browser:

ftp://utility.lpadesign.com

If the link above causes your browser to ask for authentication, then your computer has access to our FTP servers. Cancel or Close that dialogue; it just tests if your computer has general FTP access to our servers, but this dialogue is not used by the Utility.

If you get the authentication dialogue (which you can just close), but the Utility still will not download firmware files, then check any firewall, anti-malware or anti-virus software you may be running. Temporarily disable it or use it to allow FTP expressly to the PocketWizard Utility.

If you do not see the authentication dialogue, then something is blocking your computer's access to FTP. Try this:

  • Check your internet connection and verify it is working
  • Check any firewall, anti-malware or anti-virus software you may be running. Temporarily disable it or use it to allow FTP expressly to the PocketWizard Utility
  • Check with your network administrator to see if FTP is allowed on your network

If you’re still having trouble, contact PocketWizard tech support for help.

Is the Utility compatible with my operating system?

The latest version of the PocketWizard Utility works well with all recent versions of Windows (7, 8.1, 10) and the latest Mac OS, El Capitan (10.11.4). In the Read Me file, Windows 8.1 and 10 are not listed as compatible. We are currently working on a new version of the Utility that includes proper documentation.

Why are all the fields in the Utility screen grayed-out?

The Utility is trying to contact our servers and can't. Start by opening a new browser window and entering ftp.radioslave.com. If you are presented with a password window, that’s good – it means the Utility can access the necessary servers. If you are not presented with a password window, check your firewall and security settings to be sure the Utility has been allowed the necessary permissions.

If you still have trouble, contact PocketWizard tech support.

Where are all the options for advanced settings?

Click the check-box in the bottom-left corner of the Utility window (next to a picture of a small blue gear) to enable Advanced Mode and reveal additional settings.

What is the latest firmware version for my radio? Where can I find release notes?

You can find the latest firmware versions for your radios and read release notes on our Getting Started page.

What do all of these Utility selections mean, anyway?

The Utility can be used to optimize ControlTL radios for a particular desired performance. Most photographers will be able to use radios in their default settings. To read more about each Utility setting, visit our PocketWizard Utility wiki page.