Difference between revisions of "Plus III"

From PocketWizard Wiki
Jump to: navigation, search
Line 1: Line 1:
[[File:Plus III front.jpg|right|200px|The Plus III Transceiver]]
+
[[File:Plus III front.jpg|right|150px|The Plus III Transceiver]]
  
 
The Plus III is a radio transceiver, capable of acting as a transmitter or receiver for triggering remote flashes and cameras. It requires at least one other PocketWizard radio for wireless triggering. It can be connected to almost any remote flash or camera with the proper cable.
 
The Plus III is a radio transceiver, capable of acting as a transmitter or receiver for triggering remote flashes and cameras. It requires at least one other PocketWizard radio for wireless triggering. It can be connected to almost any remote flash or camera with the proper cable.
Line 9: Line 9:
  
 
===Connecting===
 
===Connecting===
{| border="0"
+
{| style="float: right;" border="0"
 
|-
 
|-
 
!colspan=3|
 
!colspan=3|
 
|-
 
|-
|[[File:P3-silhouette-1.jpg|200px]]
+
|[[File:P3-silhouette-1.jpg|150px]]
! scope="col" width="75" |
+
! scope="col" width="30" |
|[[File:P3-silhouette-2.jpg|200px]]
+
|[[File:P3-silhouette-2.jpg|150px]]
 
|-
 
|-
 
|}
 
|}
Line 30: Line 30:
  
 
==Remote Flash Triggering==
 
==Remote Flash Triggering==
 +
[[File:P3-silhouette-3.jpg|right|150px|]]
 
With transmitting and receiving PocketWizard® radios set to the same channel and zone, remote flashes will be synchronized with the camera.
 
With transmitting and receiving PocketWizard® radios set to the same channel and zone, remote flashes will be synchronized with the camera.
  

Revision as of 10:19, 27 March 2012

The Plus III Transceiver

The Plus III is a radio transceiver, capable of acting as a transmitter or receiver for triggering remote flashes and cameras. It requires at least one other PocketWizard radio for wireless triggering. It can be connected to almost any remote flash or camera with the proper cable.

Like the Plus II, the Plus III is a manual flash trigger. It is compatible with all other PocketWizard radios operating on the same frequency. Learn more about the frequencies we use on our Frequency Page. It can transmit and receive on Standard Channels, not the ControlTL Channels used by some other radios for TTL flash and power control.


Plus III Basics

Connecting

P3-silhouette-1.jpg P3-silhouette-2.jpg

Connect a Plus III to your camera via the hot shoe. This will be your transmitting radio. Connect a Plus III to each of your remote flashes using the appropriate sync cable. These will be your receiving radios. If you are using a camera with no hot shoe, or the hot shoe cannot be used, connect the transmitting Plus III’s Flash/Camera Port to the camera’s sync terminal. Visit PocketWizard.com/support/cable_finder for correct camera cable.

Powering On/Off

Make sure batteries are properly installed. To turn on your Plus III, hold down the Power/MODE Button for about two seconds. The Status LED blinks green every few seconds to indicate normal operation. It will blink red in sync with a trigger. Hold down the Power/MODE Button for about two seconds to turn off your Plus III.

Channels & Zones

Your Plus III needs to be on the same channel as other PocketWizard radios. Channels can be set via the Plus III’s Channel Up/Down Buttons . When using Channels 17-32, you can specify Zones A, B, C, and D. See “Channels and Zones” section for more info.


Remote Flash Triggering

P3-silhouette-3.jpg

With transmitting and receiving PocketWizard® radios set to the same channel and zone, remote flashes will be synchronized with the camera.

  1. Attach a Plus III to your camera’s hot shoe. You may also connect the Plus III radio to your camera’s PC sync port using the included cable.
  2. Connect a Plus III to your remote flash via the appropriate sync cable.
  3. Select Channel and Zone A, B, C, or D via Channel Up/Down Buttons and Zone Toggle Buttons. Set any other PocketWizard radios to a matching Channel and Zone. See the “Using Zones” section for more information.
  4. Take pictures normally at or below your camera’s X-sync speed.

Momentarily pressing the TEST button will test trigger the flash.


Remote Camera Triggering

With transmitting and receiving PocketWizard® radios set to the same channel and zone, remote flashes will be synchronized with the camera.

  1. Connect Plus III to your remote camera via the appropriate remote camera cable.
  2. Select Channel and Zone A, B, C, or D via the Channel Up/Down Buttons and Zone Toggle Buttons.
  3. Press the TEST button on the transmitting PocketWizard radio or fire the camera in your hands. The remote camera will trigger.

If the transmitting PocketWizard radio in your hands is a Plus III, you can pre-release the remote camera by pressing the TEST button half way. This wakes up the remote camera and lets it respond more quickly and consistently. It can also engage autofocus.