Difference between revisions of "Nikon D3"
(→HyperSync Performance) |
|||
| Line 15: | Line 15: | ||
==HyperSync Performance== | ==HyperSync Performance== | ||
| − | Use the tables below to view the D3's HyperSync performance with a specific flash. | + | Use the tables below to view the D3's HyperSync performance with a specific flash. |
| + | |||
| + | {{NikonHyperSyncSteps}} | ||
| + | |||
| + | <br /> | ||
===Elinchrom=== | ===Elinchrom=== | ||
Revision as of 11:33, 26 June 2013
Review this page for information about the Nikon D3 and its performance with PocketWizard radios.
Contents
General Nikon Operational Considerations
The following operational considerations apply to all Nikon cameras unless otherwise noted.
Flash Sync Speed - Custom Camera Setting
When using a Nikon camera and ControlTL radios, the camera's "Flash Sync Speed" setting must be set to the slower shutter speed of the two "Auto FP" options. This setting can be found in the "Bracketing/Flash" Custom Settings menu.
D3 Specific Operational Considerations
The following operational considerations apply only to the D3.
Camera Firmware
For best results, use the latest camera body firmware. The latest firmware for the D3 is A:2.03 / B:2.03, available for download at Nikon Service & Support.
HyperSync Performance
Use the tables below to view the D3's HyperSync performance with a specific flash.
- Find the table for your flash brand and PocketWizard receiver.
- Locate your flash in the "Flash Model" column.
- Determine whether you will enable HyperSync Only or not. Enabling HyperSync Only will provide the most consistent results and is recommended for Nikon users.
- Follow the "Transmitter Setup" link in the "Radio Setup" column to configure your transmitter.
- Follow the appropriate Receiver Setup link in the "Radio Setup" column. When configuring your receiver, you will need to choose a HyperSync Automation method, either Reduced Clipping or Highest Energy.
- Choose the PDF that corresponds to the HyperSync Automation method that you have selected for your radios. The PDFs contain images that illustrate the kind of performance you should expect with your setup.
Elinchrom
| Ranger RX S-Head | HyperSync Only Enabled | Highest Energy | Reduced Clipping |
| HyperSync Only Disabled | Highest Energy | Reduced Clipping | |
| Ranger RX A-Head | HyperSync Only Enabled | Highest Energy | Reduced Clipping |
| HyperSync Only Disabled | Highest Energy | Reduced Clipping |
AlienBees
| AlienBees B1600 | HyperSync Only Enabled | Highest Energy | Reduced Clipping |
| HyperSync Only Disabled | Highest Energy | Reduced Clipping |
| Don't see your gear? |
|---|
| We have paused our HyperSync testing and PDF production for the time being. We may be adding more results to the wiki as they become available. Check back in the future. |
Nikon Special Notes
The following special notes apply to all Nikon cameras.
FV Lock
FV Lock is not currently supported with PocketWizard radios.
Unsupported Modes
- Mirror Up mode is not fully supported at this time – test with your specific configuration before using.
- Exposure Delay mode (set via in-camera menu) is not currently supported.
- Repeater/RPT mode is not currently supported.
In-Camera Flash Control
Using in-camera “Flash Control for Built In Flash” menu to control remote zones is not currently supported.
Rear-Curtain Sync and Bulb
Rear Curtain Sync and Bulb mode cannot be used together. For more information, visit our Rear Curtain Sync page.
Remote Infrared Control
ControlTL radios disable ALL infra-red/optical communication pulses used in Nikon’s native i-TTL system, and will not trigger remote flashes configured to receive these pulses. A PocketWizard radio is required for each remote flash you want to trigger.
| Do you need personalized customer service? |
|---|
| If you need more information or personalized assistance, please contact us via our Inquiries Page. |
