Canon 1D X

From PocketWizard Wiki
Revision as of 13:30, 12 June 2013 by Steve (Talk | contribs)

Jump to: navigation, search

Review this page for information about the Canon 1D X and its performance with PocketWizard radios.


Camera-Specific Operational Considerations

Limited Compatibility, No TTL

FEC table.png

TTL is not currently available for the 1D X with ControlTL radios. Manual power control for X-synx, manual power control for HSS, HyperSync, and Rear Curtain Sync are all available. An AC3 ZoneController with the zone set to “M” for Manual, and manual power control of compatible flashes like Einstein E640, AlienBees, White Lightning, and select Elinchrom flashes will also work.


Manual-Only Operational Considerations:

  • For remote manual power control to work, remote Speedlites on FlexTT5 radios must be set to TTL, as is normal operation for the ControlTL system.
  • A Master Speedlite on the camera’s radio set to E-TTL mode will not trigger. Any remote zones set to TTL will not trigger.
  • A Master Speedlite on the camera’s radio set to manual mode, with or without remote manual zones, will function normally.
  • The Canon 600EX-RT Group and ALL modes are not supported in the ControlTL system for any Canon cameras, including the 1D X, 6D, and T4i. Master Manual Mode works properly with these cameras.
  • An AC3 ZoneController will not trigger any zones set to A for either TTL remotes (Speedlites) or PowerTracking studio remotes.
  • If the 1D X, 6D, or T4i are woken up with a very quick full-press of the camera’s shutter release, flashes may misfire or clipping may occur. Try to always wake the camera with a slow, deliberate half-press of the shutter release before taking the exposure. On the 1D X, consider setting C.Fn6 (“Timer Duration”) to 1 min or longer to keep the camera awake longer after a full-press.
  • When using a bare shoe FlexTT5 or MiniTT1 on the 1D X, 6D, or T4i (no Master Speedlite and no AC3 ZoneController), the camera’s FEC adjustment can adjust the manual power of remote Speedlites or studio flashes per the table to the right ->
  • This adjustment is not real time. To apply an FEC adjustment, either wait for the camera to sleep, and then wake it with a half-press of the shutter release button, *or* press the FEC button, make your adjustment, and then press the FEC button again to “set” the adjustment.
  • On cameras other than the 1D X, 6D, or T4i, using a bare shoe MiniTT1 or FlexTT5 (no AC3 ZoneController or Master Speedlite) would cause the remote flashes to be used as TTL flashes, with FEC controlling compensation to output power in real time.
  • Only the “Full Manual” PowerTracking mode is available for the 1D X, 6D, and T4i. If other PowerTracking modes, like “Center on ISO & Aperture” are selected, they will perform as “Full Manual.” “No Change (Trigger Only)” will work as expected.


HyperSync Performance

Use the grid below to view examples of the 1D X's HyperSync performance with a specific flash. Find your desired light in the left-hand column and select either "Highest Energy" or "Reduced Clipping" to download a PDF of the results.

Einstein Highest Energy Reduced Clipping
Ranger RX A-Head Highest Energy Reduced Clipping
AlienBees B1600 Highest Energy Reduced Clipping

NOTE: All of the images contained in this table were captured using a MiniTT1 or FlexTT5 transmitter and a ControlTL receiver (such as the FlexTT5 with AC9 Adapter, PowerST4, or PowerMC2).


Don't see your gear?
We have paused our HyperSync testing and PDF production for the time being. We may be adding more results to the wiki as they become available. Check back in the future.