PowerMC2

From PocketWizard Wiki
Revision as of 08:48, 31 August 2011 by Ian (Talk | contribs)

Jump to: navigation, search

Receiver with ControlTL® for Einstein­™ E640 Flash

PWPOWERMC2.jpg

The PowerMC2 Receiver Module enables remote power control of Einstein™ E640 flashes using PocketWizard ControlTL technology. With a MiniTT1 Transmitter or FlexTT5 Transceiver on your camera and a PowerMC2 plugged into your Einstein™ E640 flash, you can now adjust the flash power settings directly from the camera position. Add the AC3 ZoneController and you can control three different zones of lights in 1/3-stop increments with up to a six-stop range. Utilize PocketWizard’s unique features such as HyperSync and Optimized Rear Curtain Sync for maximum control of your lighting.

Special Warning

When connecting the PowerMC2 to the PocketWizard Utility, make sure to disconnect the PowerMC2 from any attached flash first.

Do not connect the PowerMC2 to USB while also connected to the Einstein E640 flash. Damage to your PowerMC2, Einstein, or Computer's USB port could result.

Using your PowerMC2

PowerMC2Einstein.jpg

1. Connect the PowerMC2 to your Einstein™ E640 Flash via the remote port, then power on the flash.

2. Select the Channel and Zone A, B, or C via the E640’s LCD.

3. Set up your PocketWizard transmitter and take pictures normally.

4. Adjust the camera’s Flash Exposure Compensation (FEC) to adjust the power of your remote flash. See the Basic Power Control section for more information about FEC.


Make sure all your radios are set to the same PocketWizard channel.

The Status LED blinks Green every few seconds to indicate normal operation. It will blink Red in sync with a trigger.

Momentarily pressing TEST will test trigger the flash.

Your PowerMC2 needs to be on the same channel as your transmitter. Channels can be set via the Einstein’s built-in LCD. The PowerMC2 is capable of receiving on either ControlTL Channels for use with ControlTL radios like the MiniTT1 and FlexTT5 or Standard Channels for triggering with the Plus II, MultiMAX, and Sekonic meters.

To set the channel, press the Einstein’s™ FUNCTION button until the Channel selection box is highlighted, and then change channels with the ADJUST buttons. Press the FUNCTION button again to specify a zone. When using ControlTL Channels, or Standard Channels 17-32, you can specify zone A, B, or C.

Note: When receiving on Standard Channels, the PowerMC2 will be unable to do any form of PowerTracking, or remote Manual Power Control. You must be using a ControlTL radio in ControlTL radio mode for the Einstein to be able to engage in any form of ControlTL feature.


ControlTL
Controltl.jpg

PocketWizard’s newest firmware platform taps into the camera’s digital communications to enable an entirely new level of remote flash capability through our proven radio system. ControlTL allows remote TTL systems as well as Manual Power Control. ControlTL firmware is configurable and upgradeable for “future-proof” continuous improvement.

Manual Power Control
Manual power control.jpg

Adjust the manual power settings of your remote Einstein flash directly from a AC3 ZoneController, or master flash mounted on your on-camera MiniTT1 or FlexTT5. You can independently control the power output of up to three remote groups of lights (you can have as many lights in each group as you want) from full power down to the lowest setting through the user interface on the back of the master flash or with the dials of the AC3 ZoneController. Now you can work with total control with your remote lights, without leaving your shooting position.

HyperSync
Hypersync.jpg

Our patent pending HyperSync® technology allows photographers to achieve faster X-sync speeds with full power flash. That extra speed can be used to freeze action or cut ambient light - both of which can produce results never possible before. HyperSync works automatically with the PowerMC2. All you need is a MiniTT1 or FlexTT5 on camera to gain the benefits of HyperSync. While performance varies by the camera and flash equipment being used, HyperSync will get the maximum possible out of any configuration.

PowerTracking
Powertracking.jpg

When working with certain manual flashes, you can change any of your settings on your camera and the system adjusts for those settings. Change your camera's exposure compensation to adjust the flash output, or make adjustments in aperture or ISO and the system balances your flash for proper exposure.

Basic Power Control

With only a MiniTT1 or FlexTT5 on your camera, your camera’s FEC (Flash Exposure Compensation) control will adjust your flash power output level for all your PowerMC2-connected flashes as shown in the table below.

Camera FEC/EC
- or -
AC3 Power Dial in Manual
Einstein E640 Power Output
+3 1/1
+2.7 1/2 + 0.6
+2.3 1/2 + 0.3
+2 1/2
+1.7 1/4 + 0.6
+1.3 1/4 + 0.3
+1 1/4
+0.7 1/8 + 0.6
+0.3 1/8 + 0.6
0 1/8
-0.3 1/16 + 0.6
-0.7 1/16 + 0.3
-1 1/16
-1.3 1/32 + 0.6
-1.7 1/32 + 0.3
-2 1/32
-2.3 1/64 + 0.6
-2.7 1/64 + 0.3
-3 1/64

Specifications

Frequency 340.00 - 354.00 US FCC/IC
433.42 - 434.42 MHz - CE
Channels 52 Channels over 26 Frequencies - US FCC/IC
35 Channels over 5 Frequencies - CE
Antenna 2.7" (6.9 cm) rubberized
Mounting Eight-pin remote socket
Zone Select Switch A-B-C Plus channel "D" if receiving on a MultiMAX channel.
Status Indicator LED: Green, Amber, Red Status indications
USB USB Compliant 2.0, Mini-B Connector, 5VDC regulated, 100mA, Pin 1 Positive, Pin 4 Ground

DO NOT CONNECT RADIO TO USB WHILE ALSO CONNECTED TO EINSTEIN FLASH.

Operating Temperature Above -15° C (5° F) and below 50° C (120° F)
Storage Temperature Above -30° C (22° F) and below 85° C (185° F)
Construction high impact plastic, rubberized antenna, RoHS Compliant
Power Receives power from attached flash
Dimensions 4.66" (11.84 cm) long x 1.29" (3.27 cm) wide x .43" (1.09 cm) depth
Weight .77 ounces (21.83 grams)
Requirements Must be used in conjunction with a MiniTT1 or FlexTT5 on camera for power control capability.
May be paired with any PocketWizard transmitter or transceiver for simple triggering.