Multiuser Environments

This page outlines the best practices when many photographers are simultaneously triggering remote cameras at large sporting or other events.

We are very proud of our radios. They provide rock-solid mission-critical performance in venues around the world. Thanks to our broad frequency range, powerful Custom IDs, and proven digital RF signaling methods, our MultiMAX radios can handle several photographers at the same event while providing control and exclusivity like no other remote trigger system.

But they are not originally designed to handle over 100+ photographers capturing the same finish-line moment as happens at the largest sporting events.

We continue to improve operation for exclusivity (Custom IDs), simultaneous use (Patterns), and greater distances (Long Range Mode). But too many photographers on the same frequency can still be a concern. Please read this information to learn the best methods to increase your odds of getting that once-in-a-lifetime remote shot at the most crowded events.

MultiMAX

Look here for features and specifications: MultiMAX on PocketWizard.com

Quick links to:

• MultiMAX Manual
• CE Multilingual Quick Guide
• USA/FCC English Quick Guide.

New BETA firmware with Patterns has been released!

Quick Check List

Here is a quick check list to get you started:

• Upgrade your firmware to the latest that includes Patterns
• Know your frequency
• Find the Sign-up Sheet
• Set a Pattern
• Set a long contact time on your Receiver
• Use Long Range Mode on your transmitters *and* receivers
• Press and *hold* TEST or your trigger button, don’t tap it
• Use ferrite chokes on long cable runs.
• Get the receiver’s antenna as high as you can
• Maintain line of sight whenever possible
• Dress, hang, drape, run or dangle cables away from antennas
• Consider hard-wiring

Custom IDs, myths and realities

A Custom ID is a private digital code. In crowded shooting environments, Custom IDs allow only you to trigger your remote flash or camera. Other photographers cannot trigger your remotes.

A Custom ID is not a “private frequency.” It is an exclusive code installed on top of an existing PocketWizard frequency.

Too many photographers triggering simultaneously on the same frequency can be a serious issue, even for Custom ID users. Your remote might not trigger because it cannot “hear” its digital code through all the other digital codes being transmitted on that frequency. How many is too many? Hard to say, but the fewer the better in all situations!

The methods throughout this document can be used to improve operation in multiuser environments.

You can get a Custom ID on your MultiMAX, FlexTT5 or Plus III/IV In one of 3 ways:

• If you already own the radios, contact us at info@pocketwizard.com for shipping and payment information.
• If you want to buy radios from your favorite dealer, they can drop ship the radios to us. Please contact us at info@pocketwizard.com before ordering.
• If you live in the US or Canada, you can buy the radio and ID on our shop and have it shipped directly to you. (note: MultiMAX radios are no longer available for sale)

Custom IDs are $95 USD per ID per radio - this price hasn't changed since 2008.

Special Custom ID notes

• Custom IDs can only be installed on FlexTT5, Plus III, or Plus IV radios, or MultiMAX radios with USB ports. If you have an original MultiMAX (power and DC ports only) or a MultiMAX with an ACC port but no USB, please contact us at info@ocketwizard.com to see if we can install Custom IDs on your radio. They are not available for any other PocketWizard radios including PlusX, Plus II, MiniTT1, etc.
• The MultiMAX has been retired: MultiMAX Retirement Announcement
• You can buy Plus III/IV and FlexTT5s radios directly from PocketWizard (only in the USA) or from your local dealer or distributor. If you purchase them from your local dealer, you need to then send them to LPA Design / PocketWizard.
• Dealers and distributors do not sell radios with Custom IDs already installed. Many dealers will let you drop-ship your Plus III/IV or FlexTT5 radios directly to LPA Design for a Custom ID service.
• All MultiMAX, FlexTT5, or Plus III/IV radios that you want to work together must have the same Custom ID installed.
• Custom IDs cannot be installed via the PocketWizard Utility.
• Future firmware upgrades will not erase your Custom IDs. They are permanent.
• You can get more than one Custom ID on a radio. Each additional ID is $95 per radio.
• LPA Design / PocketWizard maintains a database of Custom ID holders. Only you can get your Custom ID on future radios.
• Custom IDs are exclusively installed at LPA Design / PocketWizard in Vermont, USA.
• Purchase Custom IDs here: PocketWizard Shop

Know your frequency

More important than knowing your Custom ID is knowing what frequency it is using. At any large event, the goal is to have as few photographers sharing a single frequency as possible.

If you have a USB-capable FCC MultiMAX with firmware version 7.50 or higher, you can move your Custom ID to different frequencies. Even though the Custom ID appears on Channel 17, it will use the frequency you set in the radio. Set the frequency under the Other Functions/Custom ID menu.

If you have a non-USB FCC MultiMAX,Plus III,Plus IV, or FlexTT5", your Custom ID is locked on a single frequency.

• If your Custom ID is on Channels 17 - 32, the last digit of your Custom ID determines the frequency. See the table below. Even though your Custom ID may appear on Channel 17, it is likely using a different frequency to transmit.
• If your Custom ID is on Channel 1 - 16 then your frequency is 344.04 MHz, the same frequency used by all PocketWizard Classics, Plus, Plus II, and other radios on Standard Channels 1 - 16.

Learn more on the Channels page.

To see your Custom ID, simply turn on your MultiMAX. It should show as part of the power-up sequence. You can also hold "A" on your MultiMAX as you power it on to display your Custom ID(s).

If you have a Plus III/IV with a Custom ID, it will show "CC" before the Channel instead of "CH". There should be a label inside the battery compartment with your ID information.

If you have a FlexTT5 with a Custom ID, you will see a label under the antenna. Note: the frequency will not be reflected in the Utility. You will need to refer to the sticker or document the Channel elsewhere.

Non-USB FCC MultiMAX
Last Digit of Custom ID	Frequency (MHz)
0	354
1	353.5
2	353
3	352.5
4	352
5	351.5
6	351
7	350.5
8	350
9	349.5
A	349
B	348.5
C	348
D	347.5
E	347
F	346.5

There are some Custom IDs in use that do not follow this table. If you are unsure, contact LPA Design for more information. We will research your radio in our database and help you understand which frequency you are actually using.

CE MultiMAX radios only have 1 frequency for all Custom ID use due to regulatory limitations. USB CE MultiMAX radios can use Patterns to get more simultaneous users. Non-USB CE MultiMAX radios do not have access to Patterns.

Use a Sign-Up sheet

Anyone at an event, or an event coordinator, can help make sure all photographers have the best experience by using a sign-up sheet. Here is an example:

media:Multiuser_Sign-Up_Sheet_Example.pdf

The goal of the sign up sheet is to minimize the number of users per frequency.

Set a Pattern

There can be multiple Custom IDs triggering on the same frequency at very large sporting events. Your Custom ID will prevent someone else from triggering your camera, but it won’t prevent someone else from stepping on your trigger signal and potentially canceling out the triggers.

MultiMAX firmware 7.51 or later has a feature called Patterns. Patterns help when there are multiple photographers triggering on the same frequency. When you press and hold TEST on your MultiMAX, repeated triggers are being sent at a steady pace. If your triggers overlap with another photographers, neither of your remote cameras will fire. Patterns help keep repeating triggers from overlapping and dramatically reduce the possibility of cancelling each other out on the same frequency.

Patterns are only helpful for remote camera triggering. They are not helpful for remote flash triggering.

For USB FCC MultiMAX radios with Custom IDs, Patterns are set under the Other Functions/Custom ID menu. This menu only appears if you have Custom IDs installed in your USB FCC MultiMAX with firmware 7.51 or later.

For USB CE MultiMAX radios, with or without Custom IDs, Patterns are handled differently. Channels 17 – 32 are all on the same frequency already, so Patterns are available without Custom IDs installed. Select a Pattern under the Other Functions/Custom ID menu, and make sure to set a different channel or Custom ID from other CE photographers.

Patterns are only available for USB MultiMAX radios, FCC or CE. MultiMAX radios without USB ports, FlexTT5s, Plus IIIs, and Plus IVs cannot take advantage of Patterns.

Learn more about Patterns here: MultiMAX BETA Firmware 7.51 Release Notes

Another description of Patterns is available at SportsShooter.com.

Engage Long Range Mode

MultiMAX firmware version 7.50 and later has a special feature called Long Range Mode.

Long Range Mode increases the usable distance, up to double, between two MultiMAX radios. This mode must be activated on all radios that are expected to work together. When it is activated on a transmitter, LT will be displayed. When it is activated on a receiver, -LR- will be displayed. Long Range Mode is designed primarily for remote camera triggering.

Long Range Mode is set under the Other Functions/Range Mode menu.

Long Range Mode is only available for USB MultiMAX radios, FCC or CE. MultiMAX radios without USB ports cannot take advantage of Long Range Mode.

Long Range Mode can be used with Custom IDs and Patterns. Use longer Contact Times and hold TEST when triggering instead of tapping. This is the recommended configuration for triggering a remote camera at any large sporting event.

Don't use Repeater Mode

Repeater Mode is a very handy function for extending range when you are the only user on your frequency. When you are sharing a frequency with other photographers, it is not recommended. Improperly deployed Repeater Mode radios can add extra trigger signals causing the same trigger overlapping problem that Patterns is used to correct.

Set Longer Contact Times in your Receiver

Contact time controls how long a receiver holds the shutter button pressed on your remote camera after it receives a radio trigger. It is always set on your receiving MultiMAX. Setting it on your transmitter has no effect on remote cameras.

A longer contact time on your receiver helps RF performance in a crowded multiuser environment. If your remote MultiMAX receives a single correct RF trigger packet over the air, it will trigger your camera for the duration of the contact time. If another single RF trigger packet makes it through before the contact time finishes, it will continue holding the camera triggered. It only takes a very few trigger packets to get a long motor drive burst which may yield more usable finish line results.

EXAMPLE: You want a remote finish line camera to trigger a lot of frames right at the end of the race. Set your contact time to a reasonable burst length. If your camera can do 6 FPS in high speed drive mode, consider setting your contact time to 1 second. Any single RF trigger packet received will guarantee you get at least 6 images.

Contact time is set in a MultiMAX under the Basic Settings menu. Adjust using the letter and arrow keys.

Hold TEST, don’t tap it

When triggering a remote camera in a crowded environment, you will get better results if you press and hold the TEST or trigger button on your transmitting radio. Pressing and holding TEST will put hundreds more trigger packets into the air for your receivers to hear. Tapping TEST, or pressing and releasing it rapidly, will put fewer trigger packets in the air. The more trigger packets that are sent, the higher chance your remote receiver will hear one!

Plus III/IV

The Plus III/IV can be used at large events, and get Custom IDs installed, but it cannot use the new MultiMAX Patterns. A USB MultiMAX with a Custom ID is the preferred solution.

On the Sign-Up Sheet, Plus III/IVs must use the first column only: “No Custom ID and/or non-Pattern radios.” Plus III/IV Channels use the same Standard Channel Numbers and Frequencies as MultiMAX and ControlTL radios.

Using ControlTL radios: MiniTT1 and FlexTT5

ControlTL radios like the MiniTT1 and FlexTT5 can be used for remote camera triggering, and offer a few more frequency choices, however there are some important considerations.

FlexTT5s can get Custom IDs installed but cannot use MultiMAX Patterns. A USB MultiMAX with a Custom ID is the preferred solution. A MiniTT1 cannot get Custom IDs installed.

FCC ControlTL radios share some frequencies with the FCC MultiMAX. CE ControlTL radios do not.

IMPORTANT

Using FCC ControlTL radios on ControlTL Channels 5-14 puts a large amount of radio packets in the air that can negatively affect all MultiMAX users on those shared frequencies. This is because a ControlTL radio transmits a lot of settings and information as it communicates with the camera, while a MultiMAX only transmits a trigger signal. If you are using a ControlTL radio at a crowded event, set your ControlTL Transmit Channel to channels 1-4 or 15-20 which do not have shared frequencies with the MultiMAX.

Remember that ControlTL radios transmit on two Channels, a Standard Channel and a ControlTL Channel. Set your Standard Channel to a frequency that is not in use, or use Standard Channel 5 (344.04 MHz) which is outside the range of modern MultiMAX Custom ID users and the Plus II.

On the Sign-Up chart, ControlTL radios must use the first column only: “No Custom ID and/or non-Pattern radios.” Note the overlapping frequencies, and try to use a non-overlapping channel.

Using the PocketWizard Utility, set the following features in your ControlTL radios:

• On your receiving FlexTT5, engage “Disable Shoe Communications” on the Misc Tab. This will allow you to trigger more quickly when the radio is mounted in the shoe of your remote camera, and will generate less radio traffic by disabling Auto-Relay Mode.
• On your transmitting MiniTT1 or FlexTT5, consider changing the settings below. This will generate less radio traffic on your frequency, benefitting other users:
  • Flash Tab / Speedlight control – set to “No Change (Trigger Only)”
  • Flash Tab / Remote Studio Controls – set both to “No Change On Wakeup”
  • PowerTracking Tab / PowerTracking control – set to “No Change (Trigger Only)”
  • Modeling Tab / Uncheck “Modeling Light Control”
  • Sleep Tab / Uncheck “Remote TTL Flash Sleep Mode”

 

Hardwire

Consider hardwiring your remote camera. The more hardwire triggers in use, the greater the reliability for all photographers at a venue, whether you are using radios or not.

Your low-voltage, low-current camera motor drive can only push so many electrons around, so give it the best conditions to do so:

• Avoid add-a-taps. These zip cord connectors are convenient, but a crimping/piercing connection can often be more fragile than other solutions like miniphone connectors. A “stale” crimp that has been spooled up is a recipe for failure – it can be physically weakened when rolled/unrolled, and unseen corrosion can cause poor connectivity.
• Soldered wires are usually better than connectors. If you have the ability to solder wires directly together instead of using snap-together connectivity, like miniphone connections or add-a-taps, you should consider it. Every “adapter” or snap-together connection represents another potential failure point.
• Use ferrite chokes. When lots of unshielded cabling like zip line is used, it can act as a big antenna for EMI. Even if you aren’t using a radio, EMI can cause you to miss triggers. Your low-voltage motor drive circuit might not be able to tell if that was your switch closing on the line, or just random electrical noise from the “Swiss timing” box. Place ferrite chokes near both ends of your hardwire run. 2 or 3, clamped 30cm or so apart, is usually enough.
• Run your hardwire as exclusively as possible. The more wires piled on top of each other, the worse EMI can be. This is especially true if your hardwire is running in the same catwalk/conduit/trough as power, AV, precision timing, scoring, or other cords and cables. If you are limited and must share space, definitely use ferrite chokes as described above.
• Polarity matters for multiple cameras. If you have more than one camera on the same hardwire, make extra sure to check that you have used the same polarity for each connection.
• Keep the run as short as possible. Avoid extra piles or loops/spools of cable as part of your setup. Spooled or looped cable gathers and amplifies EMI.

If you have any hardwire questions, feel free to ask! Even though we are a radio company, we’ve learned a thing or two about hardwiring over the years.

More coming soon!

Other topics will be posted as they are ready, like:

• Buddying up - multiple receivers on the same channel/Custom ID and/or multiple cameras with one receiver
• “Slaving” one camera to another - a remote camera can trigger from the shoe pulse of the camera in your hands, but is it wise? (probably not!)
• Understanding Confirmation
• And more!