HyperSync Setup

This page describes how to configure your PocketWizard radios for using HyperSync to capture flash above X-sync. This page will provide details on configuring your radios in the PocketWizard Utility for best HyperSync performance.

HyperSync requires at least one ControlTL radio like the MiniTT1 and FlexTT5 to serve as the transmitter. Receiving radios may be ControlTL radios like the FlexTT5, PowerMC2, or PowerST4, or Standard Channel radios like the MultiMAX, Plus II, Plus III, or PlusX.

To learn what HyperSync is and how it differs from other flash sync techniques, visit the Understanding HyperSync and High Speed Sync page. For basic information on HyperSync, return to the main HyperSync page.

All ControlTL Radios – HyperSync Automation

Performing HyperSync is easiest with all ControlTL radios, transmitter and receivers. Non-ControlTL receivers (Standard Channel radios) do not have the benefit of HyperSync Automation, and require more manual adjustment for best results. While default HyperSync settings for ControlTL radios will usually provide great results, they may also be reconfigured by the photographer.

First configure your transmitting MiniTT1 or FlexTT5, and then your receiving PocketWizard radio. Steps for configuring your ControlTL transmitter and receiver are detailed below.

How to Configure the ControlTL Transmitter

When using a MiniTT1 or FlexTT5 as a transmitter to perform HyperSync, follow these steps to configure your radio.

For Nikon users:

For the most consistent results and most flash energy in frame with Nikon radios, it is highly recommended that you enable “HyperSync Only:”

1. Connect your transmitting MiniTT1/FlexTT5 to the PocketWizard Utility via USB, and check the "Advanced Mode" box
2. Navigate to the "HyperSync/HSS" tab
3. Enable “HyperSync Only”
4. Click "Apply Changes"

If the “HyperSync Only” control is left at its default (disabled) less flash energy will be captured in frame and HyperSync will not be able to optimize flash timing.

For Canon users:

For best performance with Canon radios, it is highly recommended that you manually select your camera model:

1. Connect your transmitting MiniTT1/FlexTT5 to the PocketWizard Utility via USB
2. Navigate to the "Misc” tab
3. Use the drop-down menu to select the camera model
4. Click "Apply Changes"

How to Configure the Receiving FlexTT5 and AC9 AlienBees Adapter

When using a Canon or Nikon FlexTT5 with an attached AC9 AlienBees Adapter as your receiver, follow these steps to configure your radio:

1. Connect your receiving FlexTT5 to the PocketWizard Utility via USB and make sure that the “Advanced Mode” box is checked
2. Navigate to the “HyperSync/HSS Tab” and select the flash connected to the AC9 AlienBees Adapter using the "AC9 Flash" dropdown menu
3. Set “ Optimize HyperSync Automation For:” to either "Reduced Clipping" or "Highest Energy" (default =“Reduced Clipping”)
4. Click "Apply Changes"
5. Connect the receiving FlexTT5 and AC9 AlienBees Adapter to the flash

HyperSync Automation is currently implemented for the following Paul C. Buff flashes and AC9 Adapter:

AlienBees AB400	White Lightning X800	Zeus 1250
AlienBees AB800	White Lightning X1600
AlienBees AB1600	White Lightning X3200
AlienBees ABR800 RingFlash	White Lightning Ultra1200

If you wish to use a flash that does not appear on the list above with an AC9 AlienBees Adapter, try selecting a flash of a similar power output.

How to Configure the Receiving PowerMC2

When using a PowerMC2 as your receiver, follow these steps to configure your radio:

1. Connect your PowerMC2 to the PocketWizard Utility via USB, and make sure that the “Advanced Mode” box is checked
2. Navigate to “Optimize HyperSync Automation For:” on the “HyperSync/HSS” tab; choose "Reduced Clipping" or "Highest Energy"
3. Click "Apply Changes"
4. Connect the PowerMC2 to the flash

HyperSync Automation with the PowerMC2 is intended for use with the Einstein E640 flash. Using the Einstein’s “Color” mode will provide the best results. The E640 only provides its best HyperSync results when set to full power (+3 on the AC3 ZoneController or master speedlight). Due to its IGBT design, settings lower than full power may result in clipping.

How to Configure the Receiving PowerST4

When using a PowerST4 as your receiver, follow these steps to configure your radio:

1. Connect your PowerST4 to the PocketWizard Utility via USB, and make sure that the “Advanced Mode” box is checked
2. Navigate to “Optimize HyperSync Automation For:” on the “HyperSync/HSS” tab; choose "Reduced Clipping" or "Highest Energy"
3. Click "Apply Changes"
4. Connect the PowerST4 to the flash or pack

HyperSync Automation is currently implemented for the following Elinchrom flashes and PowerST4:

Style 300RX	Digital 1200RX or Digital 2400RX with Digital S Head	Ranger RX with Ranger S Head
Style 600RX	Digital 1200RX or Digital 2400RX with Digital SE Head	Ranger RX with Ranger A Head
Style 1200RX	Digital 1200RX or Digital 2400RX with Mini A Head	Ranger RX Speed with Ranger S Head
	Digital 1200RX or Digital 2400RX with Mini S Head	Ranger RX Speed with Ranger A Head
	Digital 1200RX or Digital 2400RX with A3000 Head	Ranger RX Speed A/s with Ranger S Head
	Digital 1200RX or Digital 2400RX with A6000 Head	Ranger RX Speed A/s with Ranger A Head

How to Configure the Receiving FlexTT5 P2 Port

When using a FlexTT5 as your receiver connected to a flash via the P2 port, follow these steps to configure your radio:

1. Connect your receiving FlexTT5 to the PocketWizard Utility via USB, and make sure that the “Advanced Mode” box is checked
2. Navigate to the “HyperSync/HSS” tab; use the “ P2 HyperSync Flash Duration” drop-down to select a timing setting – 10 is often a good starting-point
3. Click "Apply Changes"
4. Connect the FlexTT5 to the flash or pack via the P2 port and appropriate cable
5. If you notice clipping in frame, choose a different “P2 HyperSync Flash Duration” value - if you have a smaller flash or Speedlite connected via the P2 port, start by testing with lower numbers, if you have a studio strobe or larger flash, you will likely see the best results with higher numbers

ControlTL Transmitter, Standard Receiver

Performing HyperSync is possible with a ControlTL transmitter and Standard Channel receivers like the MultiMAX, Plus II, Plus III, or PlusX.

Only ControlTL radios have HyperSync settings that can be adjusted. When using Standard Channel radios as receivers, all HyperSync settings or offsets will need to be manipulated on the transmitter. The Standard Channel receivers need only be set to use the correct channel and then connected to the remote flashes.

The transmitting MiniTT1 or FlexTT5 can account for the flash duration of remote flashes in one of two ways, “ HyperSync Flash Duration For Standard Channels” or “ Manual HyperSync For Standard Channels.” Find more information on these options on the HyperSync/HSS Tab page.

When using a mix of ControlTL and Standard Channel radios to perform HyperSync, determine whether you would like to use “HyperSync Flash Duration For Standard Channels” or “Manual HyperSync For Standard Channels.” and follow the instructions below.