Difference between revisions of "PowerMC2"

Revision as of 11:42, 1 June 2022

Receiver with ControlTL® for Einstein­™ E640 Flash

The PowerMC2 Receiver Module enables remote power control of Einstein™ E640 flashes using PocketWizard ControlTL technology. With either a Raven by Fusion TLC or MiniTT1 Transmitter or a FlexTT5 / FlexTT6 Transceiver on your camera and a PowerMC2 plugged into your Einstein™ E640 flash, you can now adjust the flash power settings directly from the camera position. Add the AC3 ZoneController and you can control three different zones of lights in 1/3-stop increments with up to a six-stop range. Utilize PocketWizard’s unique features such as HyperSync and Optimized Rear Curtain Sync for maximum control of your lighting.

The PowerMC2 can also be used with any PocketWizard using Standard Channels as well, such as a Plus II or MultiMAX. You will need to adjust power levels on the Einstein itself when using these radios but if you are using Channels with Zones, you will be able to enable and disable the Zone from the transmitting radio. Please see the note below to learn how to choose the proper Channel on the Einstein.

Setting up your PowerMC2

1. Update the firmware in your PowerMC2 to the most current version.

NOTE: When connecting the PowerMC2 to the PocketWizard Utility, make sure to disconnect the PowerMC2 from any attached flash first.

Do not connect the PowerMC2 to USB while also connected to the Einstein E640 flash. Damage to your PowerMC2, Einstein, or computer's USB port could result.

2. Connect the PowerMC2 to your Einstein™ E640 Flash via the remote port, then power on the flash.

3. Select the Channel and Zone via the E640’s LCD. (see details below)

4. Disable the Einstein's optical flash (2 downward arrows).

4. Set up your transmitting radio and take pictures normally.

5. If using CTL Channels, adjust the camera’s Flash Exposure Compensation (FEC) or use the transmitting radio or AC3 to adjust power to your remote flash(es). See the Basic Power Control section for more information about FEC.

The Status LED blinks Green every few seconds to indicate normal operation. It will blink Red in sync with a trigger.

Momentarily pressing TEST will test trigger the flash.

Channels and Zones

Your PowerMC2 needs to be on the same Channel as your transmitter. Channels can be set via the Einstein’s built-in LCD. The PowerMC2 is capable of receiving on either ControlTL Channels (CTL) for use with ControlTL radios like the MiniTT1 and FlexTT5 or Standard Channels (CH) for triggering with the Plus II, MultiMAX, and Sekonic meters.

To set the channel, press the Einstein’s™ FUNCTION button until the Channel selection box is highlighted, and then change channels with the ADJUST buttons. Press the FUNCTION button again to specify a Zone.

PocketWizard Standard Channels CH01-CH32 (using a Plus or MultiMAX as the transmitter with Legacy firmware)

• Available Standard Channels 1-32.
• Power Control is not available with Standard Channels.
• Channels 17-32 will also have Zones A, B, C, and D. Zones are not available for Channels 1-16.
• You can enable or disable a Zone from a master controller if using Channels 17-32.

PocketWizard ControlTL Channels CTL01-CTL20 (Using PocketWizard MiniTT1/FlexTT5/FlxTT6 as the transmitter with Legacy firmware)

• Available ControlTL Channels 1-20.
• All Channels will have Zones A, B, and C.
• Power Control is available with ControlTL Channels.

PocketWizard E Release Channels CTL01-CTL20 (using PocketWizards that have been upgraded to the E Release or the Raven as the transmitter)

• Choose ControlTL Channels 1-20. E Channels 21-32 are not available at this time.
• All Channels will have Zones A, B, and C.
• Power Control is available with ControlTL Channels.

Your PowerMC2 needs to be on the same Channel as your transmitter. Channels can be set via the Einstein’s built-in LCD. The PowerMC2 is capable of receiving on either ControlTL Channels (CTL) for use with ControlTL radios like the MiniTT1 and FlexTT5 or Standard Channels (CH) for triggering with the Plus II, MultiMAX, and Sekonic meters.

PowerMC2 FAQ

Having trouble with your PowerMC2? Check out our PowerMC2 FAQ page!

E Release

MC2 is meant to be controlled from the new Raven for the most advanced full feature operation.

PowerMC2 Features

Manual Power Control

Adjust the manual power settings of your remote Einstein flash directly from a AC3 ZoneController, or master flash mounted on your on-camera MiniTT1 or FlexTT5. You can independently control the power output of up to three remote groups of lights (you can have as many lights in each group as you want) from full power down to the lowest setting through the user interface on the back of the master flash or with the dials of the AC3 ZoneController. Now you can work with total control with your remote lights, without leaving your shooting position.

HyperSync

Our patent pending HyperSync® technology allows photographers to achieve faster X-sync speeds with full power flash. That extra speed can be used to freeze action or cut ambient light - both of which can produce results never possible before. HyperSync works automatically with the PowerMC2. All you need is a MiniTT1 or FlexTT5 on camera to gain the benefits of HyperSync. While performance varies by the camera and flash equipment being used, HyperSync will get the maximum possible out of any configuration.

PowerTracking

When working with certain manual flashes, you can change any of your settings on your camera and the system adjusts for those settings. Change your camera's exposure compensation to adjust the flash output, or make adjustments in aperture or ISO and the system balances your flash for proper exposure.

Note that Flash Exposure Compensation can also be dialed in on a per-flash basis, by changing the PowerMC2's settings in the Exposure Tab of the PocketWizard Utility.

Basic Power Control

With only a MiniTT1 or FlexTT5 on your camera, your camera’s FEC (Flash Exposure Compensation) control will adjust your flash power output level for all your PowerMC2-connected flashes as shown in the table below.

Specifications