Status LED - Revision history

Heathers: /* Normal Operation */

2019-09-15T19:57:59Z

‎Normal Operation

2013-09-20T17:59:31Z

‎Normal Operation

2013-09-05T18:35:21Z

‎Normal Operation

2012-10-25T13:16:25Z

‎Reset

2012-10-25T13:14:53Z

‎Error Condition

2012-10-25T13:13:58Z

‎Learn Mode

2012-10-25T13:13:01Z

‎Normal Operation

2012-10-24T19:11:11Z

‎Reset

2012-10-24T19:04:23Z

‎Error Condition

2012-10-24T19:02:37Z

‎Learn Mode

@@ Line 7: / Line 7: @@
 == Normal Operation ==
-Under normal operation the LED will display a short green blink every 2 seconds. This is the normal “powered on and waiting for trigger” blink.
+When you first turn on the radio, you will see a specific power on signal.
 ;LED Blink:

@@ Line 16: / Line 16: @@
 <span style="color:red;">Red</span> blinks = Less than 25% remaining – change immediately
-<videoflash>mF-QD999nDY&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash>
+<videoflash>ooEGUQ4yX2g&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash>
 {|
+|

@@ Line 9: / Line 9: @@
 Under normal operation the LED will display a short green blink every 2 seconds. This is the normal “powered on and waiting for trigger” blink.
-!The color of the LED indicates battery level:
+;LED Blink:
-:<span style="color:green;">Green</span> = Good battery
+<span style="color:green;">Green</span> blink = More than 50% remaining
-:<span style="color:orange;">Amber</span> = Warning – battery low
-:<span style="color:red;">Red</span> = Very low battery – change immediately
+<span style="color:orange;">Amber</span> blinks = Warning – less than 50% remaining
 <videoflash>mF-QD999nDY&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash>

@@ Line 54: / Line 54: @@
 If TEST is held on power up then RESET A and RESET B can be performed. Two green blinks in a row indicate that RESET A was completed. Four green blinks in a row appear when RESET B has been completed. RESET A resets channels learned in the field back to those programmed via the PocketWizard Utility. RESET B sets the radio to factory default settings.
-<videoflash>b1ZUvRgk-0Y&loop=1&autoplay=0&autohide=1|225|155</videoflash>
+<videoflash>b1ZUvRgk-0Y&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash>
 {|
+|
 |}

@@ Line 43: / Line 43: @@
 == Error Condition ==
 Repeated red blinking indicates an error condition. Power off the unit, reseat all connections, and power back on. If the error persists, verify your settings. For example if you are using a Standard channel to trigger a FlexTT5 with a Speedlite in it set to E-TTL, this is an error. The flash needs to be set to manual (See [[Manual Mode]] for more information).
-<videoflash>0lHtF_8HyiE&loop=1&autoplay=0&autohide=1|225|155</videoflash>
+<videoflash>0lHtF_8HyiE&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash>
 {|
+|

@@ Line 31: / Line 31: @@
 If TEST is held for 10 seconds, LEARN mode will be activated.  See [[Learn Mode]] for information. A short red blink in sync with the camera’s trigger indicates normal transmission or reception.
-<videoflash>vV0tLU03OAg&loop=1&autoplay=0&autohide=1|225|155</videoflash>
+<videoflash>vV0tLU03OAg&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash>
 {|
+|

@@ Line 14: / Line 14: @@
 :<span style="color:red;">Red</span> = Very low battery – change immediately
-<videoflash>mF-QD999nDY&loop=1&autoplay=0&autohide=1|225|155</videoflash>
+<videoflash>mF-QD999nDY&loop=1&rel=0&autoplay=0&autohide=1|225|155</videoflash>
 {|
+|
 |}
-FlexTT5 "Good Battery" Blink
+FlexTT5 "Good Battery" Blink[[File:Example.jpg]]