Sleep Tab - Revision history

Seth: /* Remote TTL Flash Sleep Mode */

2012-09-10T21:53:03Z

‎Remote TTL Flash Sleep Mode

Chris at 16:03, 31 August 2011

2011-08-31T16:03:51Z

Ian at 18:36, 29 August 2011

2011-08-29T18:36:03Z

Zachary at 19:55, 21 December 2010

2010-12-21T19:55:50Z

Zachary at 22:02, 7 December 2010

2010-12-07T22:02:51Z

Zachary at 21:18, 7 December 2010

2010-12-07T21:18:30Z

Zachary: Created page with "'''Remote TTL Flash Sleep Mode''' Normally your ControlTL transmitter tells all remote TTL flashes to sleep when the camera sleeps. This saves batteries in the remote flash but ..."

2010-12-07T20:09:21Z

Created page with "'''Remote TTL Flash Sleep Mode''' Normally your ControlTL transmitter tells all remote TTL flashes to sleep when the camera sleeps. This saves batteries in the remote flash but ..."

New page

'''Remote TTL Flash Sleep Mode'''

Normally your ControlTL transmitter tells all remote TTL flashes to sleep when the camera sleeps. This saves batteries in the remote flash but could cause the flash to take a moment to be ready before the next trigger. Enable this control to have your ControlTL transmitter wait to tell all remote E-TTL II flashes to sleep until a time after the camera sleeps. This control can be independently over-ridden by a remote flash using

'''Remote TTL Flash Sleep Delay'''

Sets the number of seconds after the camera sleeps (meters go inactive) when remote TTL flashes will go to sleep.

'''Local Flash Sleep Mode''' (FlexTT5 Only)

If you are using a standard transmitter like a Plus or MultiMAX, the sleep command is never issued and the remote flash mounted on the FlexTT5 would always remain powered on. Enabling this control causes the FlexTT5 connected flash to remain awake for a set period after any radio activity, then enter its sleep mode for power saving. This control overrides Remote TTL Flash Sleep Mode.

'''Local Flash Flash Sleep Delay'''

Sets the number of seconds after the camera sleeps (meters go inactive) when a locally connected flash will go to sleep.

@@ Line 8: / Line 8: @@
 ====Remote TTL Flash Sleep Mode====
-Normally your ControlTL transmitter tells all remote TTL flashes to sleep when the camera sleeps. This saves batteries in the remote flash but could cause the flash to take a moment to be ready before the next trigger. Enable this control to have your ControlTL transmitter wait to tell all remote E-TTL II flashes to sleep until a time after the camera sleeps. This control can be independently over-ridden by a remote flash using
+Normally your ControlTL transmitter tells all remote TTL flashes to sleep when the camera sleeps. This saves batteries in the remote flash but could cause the flash to take a moment to be ready before the next trigger. Enable this control to have your ControlTL transmitter wait to tell all remote E-TTL II flashes to sleep until a time after the camera sleeps. This control can be independently over-ridden by a remote flash using Local Flash Sleep Mode.
-−
 ====Remote TTL Flash Sleep Delay====

← Older revision		Revision as of 16:03, 31 August 2011
Line 1:		Line 1:
	{{Utility Tab Quick Links}}		{{Utility Tab Quick Links}}
		+
		+	__TOC__
		+
		+	[[File:Sleep.jpg\|500px\|center\|Sleep Tab]]
		+
		+
	====Remote TTL Flash Sleep Mode====		====Remote TTL Flash Sleep Mode====

@@ Line 11: / Line 11: @@
 ====Local Flash Sleep Mode====
 (FlexTT5 Only)
-If you are using a standard transmitter like a Plus or MultiMAX, the sleep command is never issued and the remote flash mounted on the FlexTT5 would always remain powered on. Enabling this control causes the FlexTT5 connected flash to remain awake for a set period after any radio activity, then enter its sleep mode for power saving. This control overrides Remote TTL Flash Sleep Mode.
+If you are using a standard transmitter like a Plus or MultiMAX, the sleep command is never sent over the air, and the remote flash mounted on the FlexTT5 would always remain powered on. Enabling this control causes the FlexTT5 connected flash to remain awake for a set period after any radio activity, then enter its sleep mode for power saving. This control overrides Remote TTL Flash Sleep Mode.
-====Local Flash Flash Sleep Delay====
+====Hibernate Mode====
-Sets the number of seconds after the camera sleeps (meters go inactive) when a locally connected flash will go to sleep.
+The Paul C. Buff Einstein E640 is always drawing power when connected to a power source, even when asleep or "Hibernating" - you'll notice the PowerMC2 is operating and blinking even when the Einstein is "Off".  The PowerMC2 can Hibernate the Einstein E640 flash after a certain period of inactivity, controlled by the Hibernate Delay setting. This sets the period of time after an incoming trigger that the Einstein will Hibernate.

@@ Line 1: / Line 1: @@
-{| style="float: right;" border="1" cellspacing="0" cellpadding="2"
+{{Utility Tab Quick Links}}
-|align="center" | '''Utility Tab Quick Links'''
-|-
-|[[Updating Firmware|Update]]
-|-
-|[[Channel Tab|Channel]]
-|-
-|[[Flash Tab|Flash]]
-|-
-|[[Sync Timing Tab|Sync Timing]]
-|-
-|[[PowerTracking Tab|PowerTracking]]
-|-
-|[[Modeling Tab|Modeling]]
-|-
-|[[Sleep Tab|Sleep]]
-|-
-|[[Misc Tab|Misc]]
-|}
 ====Remote TTL Flash Sleep Mode====

← Older revision		Revision as of 21:18, 7 December 2010
Line 1:		Line 1:
		+	{\| style="float: right;" border="1" cellspacing="0" cellpadding="2"
		+	\|align="center" \| '''Utility Tab Quick Links'''
		+	\|-
		+	\|[[Updating Firmware\|Update]]
		+	\|-
		+	\|[[Channel Tab\|Channel]]
		+	\|-
		+	\|[[Flash Tab\|Flash]]
		+	\|-
		+	\|[[Sync Timing Tab\|Sync Timing]]
		+	\|-
		+	\|[[PowerTracking Tab\|PowerTracking]]
		+	\|-
		+	\|[[Modeling Tab\|Modeling]]
		+	\|-
		+	\|[[Sleep Tab\|Sleep]]
		+	\|-
		+	\|[[Misc Tab\|Misc]]
		+	\|}
	'''Remote TTL Flash Sleep Mode'''		'''Remote TTL Flash Sleep Mode'''