Modeling Tab - Revision history

Chris at 16:01, 31 August 2011

2011-08-31T16:01:50Z

Ian: /* Modeling Light Control */

2011-08-29T14:22:23Z

‎Modeling Light Control

Zachary at 19:55, 21 December 2010

2010-12-21T19:55:43Z

Zachary at 22:01, 7 December 2010

2010-12-07T22:01:48Z

Zachary at 21:18, 7 December 2010

2010-12-07T21:18:21Z

Zachary: Created page with "'''Modeling Light Control''' Check this box to control modeling light behavior from the transmitter. '''Control Mode:''' Determines when the modeling light will go to its act..."

2010-12-07T20:08:06Z

Created page with "'''Modeling Light Control''' Check this box to control modeling light behavior from the transmitter. '''Control Mode:''' Determines when the modeling light will go to its act..."

New page

'''Modeling Light Control'''

Check this box to control modeling light behavior from the transmitter.

'''Control Mode:'''

Determines when the modeling light will go to its active setting. Set to 'Camera Wake' to have the modeling light go active when the camera's shutter release is half-pressed. Set to 'AF-Assist' to have the modeling light go active only when the camera requests auto-focus assist.

'''Modeling Light Autotrack'''

Enable this control for the modeling light level to track with the camera exposure or AC3 Power Dial settings.

'''Modeling Light Active XX%'''

Sets the active output level of the modeling light if Autotrack is not used.

'''Modeling Light Sleep'''

Check this box to have the modeling light automatically go to a set output level after a set time. If this box is unchecked, the modeling light will never sleep.

'''Modeling Light Sleep XX%'''

Sets the output level of the modeling light when it sleeps.

'''Modeling Light Delay After Camera Sleeps'''

Sets the number of seconds after the camera sleeps (meters go inactive) when the modeling light will go to its sleep value.

← Older revision		Revision as of 16:01, 31 August 2011
Line 1:		Line 1:
	{{Utility Tab Quick Links}}		{{Utility Tab Quick Links}}
		+
		+	__TOC__
		+
		+	[[File:Modeling.jpg\|500px\|center\|Modeling Tab]]
		+
	====Modeling Light Control====		====Modeling Light Control====

← Older revision		Revision as of 14:22, 29 August 2011
Line 4:		Line 4:
	Check this box to control modeling light behavior from the transmitter.		Check this box to control modeling light behavior from the transmitter.

		+	Un-checking this box is recommended when using battery powered remote studio strobes to disable Modeling Light commands from being sent over the air. This effectively disables the modeling light - however, the remote modeling can still be enabled manually via the remote flash's control panel.

	====Control Mode:====		====Control Mode:====

@@ Line 1: / Line 1: @@
-{| style="float: right;" border="1" cellspacing="0" cellpadding="2"
+{{Utility Tab Quick Links}}
-|align="center" | '''Utility Tab Quick Links'''
-|-
-|[[Updating Firmware|Update]]
-|-
-|[[Channel Tab|Channel]]
-|-
-|[[Flash Tab|Flash]]
-|-
-|[[Sync Timing Tab|Sync Timing]]
-|-
-|[[PowerTracking Tab|PowerTracking]]
-|-
-|[[Modeling Tab|Modeling]]
-|-
-|[[Sleep Tab|Sleep]]
-|-
-|[[Misc Tab|Misc]]
-|}
 ====Modeling Light Control====

← Older revision		Revision as of 21:18, 7 December 2010
Line 1:		Line 1:
		+	{\| style="float: right;" border="1" cellspacing="0" cellpadding="2"
		+	\|align="center" \| '''Utility Tab Quick Links'''
		+	\|-
		+	\|[[Updating Firmware\|Update]]
		+	\|-
		+	\|[[Channel Tab\|Channel]]
		+	\|-
		+	\|[[Flash Tab\|Flash]]
		+	\|-
		+	\|[[Sync Timing Tab\|Sync Timing]]
		+	\|-
		+	\|[[PowerTracking Tab\|PowerTracking]]
		+	\|-
		+	\|[[Modeling Tab\|Modeling]]
		+	\|-
		+	\|[[Sleep Tab\|Sleep]]
		+	\|-
		+	\|[[Misc Tab\|Misc]]
		+	\|}
	'''Modeling Light Control'''		'''Modeling Light Control'''

@@ Line 18: / Line 18: @@
 |[[Misc Tab|Misc]]
 |}
-'''Modeling Light Control'''
+====Modeling Light Control====
 Check this box to control modeling light behavior from the transmitter.
-'''Control Mode:'''
+====Control Mode:====
 Determines when the modeling light will go to its active setting. Set to 'Camera Wake' to have the modeling light go active when the camera's shutter release is half-pressed. Set to 'AF-Assist' to have the modeling light go active only when the camera requests auto-focus assist.
-'''Modeling Light Autotrack'''
+====Modeling Light Autotrack====
 Enable this control for the modeling light level to track with the camera exposure or AC3 Power Dial settings.
-'''Modeling Light Active XX%'''
+====Modeling Light Active XX%====
 Sets the active output level of the modeling light if Autotrack is not used.
-'''Modeling Light Sleep'''
+====Modeling Light Sleep====
 Check this box to have the modeling light automatically go to a set output level after a set time. If this box is unchecked, the modeling light will never sleep.
-'''Modeling Light Sleep XX%'''
+====Modeling Light Sleep XX%====
 Sets the output level of the modeling light when it sleeps.
-'''Modeling Light Delay After Camera Sleeps'''
+====Modeling Light Delay After Camera Sleeps====
 Sets the number of seconds after the camera sleeps (meters go inactive) when the modeling light will go to its sleep value.